Monday, November 11, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 332

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 332

TCCM

1. Key OFF. Disconnect the X1 connector at the TCSCS.

2. Key ON, engine OFF.

3. Using the L-BU probe J 35616-64B, test for 4.5-5.5 V between the 5-volt reference circuit, TCSCS harness X1 pin 11 and a good ground.

瀚慖f the voltage is greater than the specified range, test the 5-volt reference circuit for a short to voltage. If all circuits and connections test

normal, replace the TCCM.

瀚慖f the voltage is less than the specified range, test the 5-volt reference circuit for an open/high resistance or short to ground. If all circuits

and connections test normal, replace the TCCM.

4. Using the L-BU probes J 35616-64B, connect a test light between the 5-volt reference circuit, TCSCS harness X1 pin 11 and a good ground.

The test light should illuminate dimly.

瀚慖f the test light does not illuminate, obtain a different test light and repeat step 4.

5. Key OFF. Wait 30 seconds for the TCCM to shut down.

Note: The TCCM must see the added resistance of the test light on the control circuit at key ON or the TCCM will shut the control circuit

drivers OFF. Volt meters will not work for this test.

6. Using the L-BU probes J 35616-64B, connect a test light between the TCSCS harness as specified below for the LED control circuit being

tested.

7. Key ON, engine OFF.

8. Using the Special Function ability of the scan tool, command the affected LED ON and OFF. The test light should turn OFF and ON as

commanded.

瀚慖f the test light remains illuminated when commanded OFF, test the affected control circuit for a short to ground. If all circuits and

connections test normal, replace the TCCM.

瀚慖f the test light remains OFF when commanded ON, test the affected control circuit for an open/high resistance or short to voltage. If all

circuits and connections test normal, replace the TCCM.

TCSCS

1. Using the L-BU probes J 35616-65B, connect the EL-49741 - 9 V+ power source harness to the TCSCS as specified below for the LED

being tested. Connecting the harness in the opposite pins will not illuminate the LED.

2. Connect a 9 V battery to the EL-49741 - harness.

3. Verify that only the indicator being tested illuminates.

瀚慖f the indicator does not illuminate when tested or the incorrect indicator illuminates, replace the TCSCS.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Transfer Case Shift Control Switch Replacement (Without SLT) (See: Powertrain Management/Transmission Control Systems/Sensors and

Switches - Transmission and Drivetrain/Sensors and Switches - Transfer Case/Four Wheel Drive Selector Switch/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for TCSCM replacement, setup, and programming

* Transfer Case High/Low Clutch Reset (See: Transmission and Drivetrain/Transfer Case/Testing and Inspection/Symptom Related

Diagnostic Procedures/MP 3023/3024-NQH - Transfer Case/Transfer Case High/Low Clutch Reset)

MP 3010-NP0 - Transfer Case

DTC B0775

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an