2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 589
The module detects that the set point temperature has not been reached within 8.5 minutes.
B2425 0B, B2425 0E, B2430 0B, or B2430 0E
By measuring output current, the module calculates that the heating element resistance is below the minimum resistance.
B2425 0C, B2425 0D, B2430 0C, or B2430 0D
By measuring output current, the module calculates that the heating element resistance is above the maximum resistance.
B2425 1F or B2430 1F
The temperature sensor voltage is erratic or changes suddenly.
Action Taken When the DTC Sets
The heated seat cushion function for the affected seat will be disabled.
Conditions for Clearing the DTC
* The current DTC clears when the malfunction is no longer present, and the power mode changes to OFF then back to ACC or RUN.
* The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.
Reference Information
Schematic Reference
Heated/Cooled Seat Schematics ()
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Heated Seats Description and Operation (KA1) ()Heated Seats Description and Operation (KA6) ()
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Verify the type of vehicle and the heated seat system for which the DTC set.
If the DTC set in a vehicle equipped with memory, refer to Circuit/System Testing below.
If the DTC set in a hybrid vehicle without memory, refer to DTC B2425 or B2430 (HP2 w/o memory).
If the DTC set in a non-hybrid vehicle without memory, refer to DTC B2425 or B2430 (Dealer installed).
If the DTC set in the rear heated seat module, refer to DTC B2425 or B2430 (Rear seat).
Circuit/System Testing
B2425 0A, B2425 0B, B2425 0C, B2425 0D, B2425 0E, B2425 04, or B2425 1F
1. Ignition OFF, disconnect the X3 harness connector at the MSM.
2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 5 and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
3. Ignition OFF, connect the X3 harness connector at the MSM and disconnect the X1 harness connector at the MSM.
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
Diagnostic Repair parts ,Wiring Diagrams. DTC. TSB,Car, Truck, SUV & Van Acura Chrysler Infiniti Maserati Rolls-Royce Alfa Romeo Dodge Jaguar Mazda Scion Aston Martin Ferrari Jeep McLaren Smart Audi Fiat Karma Mercedes-Benz Spyker BMW Ford Kia Mini Subaru Bentley Freightliner Lamborghini Mitsubishi Tesla Bugatti GMC Land Rover Mobility Ventures Toyota Buick Genesis Lexus Nissan Volkswagen Cadillac Honda Lincoln Porsche Volvo Chevrolet Hyundai Lotus Ram