Wednesday, November 6, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1235

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1235

* Component Connector End Views (See: Diagrams/Connector Views)

* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Special Tools

DT-48493 Jumper Harness

Circuit/System Testing

Note: The drive motor generator position sensor circuits require proper circuit integrity for correct system operation. Just a few ohms of

additional circuit resistance may cause position sensor signal degradation.

* Always inspect position sensor signal connectors for proper terminal contact.

* All diagnostic connections must be made with the approved test probes to prevent the creation of poor terminal contact.

* Connectors that contain position sensor signal circuits must always be clean and dry prior to mating. Foreign material or moisture within

the connector may cause sensor signal degradation.

1. Ignition OFF, disconnect PIM X1 connector.

2. Using the Position Sensor Specification table specifications listed below, test the position sensor resistance at the PIM X1 circuits as

indicated. Also test each circuit for a short to ground.

瀚慖f any of the circuits are not within specification, continue with testing.

瀚慖f all circuits test normal, inspect for proper terminal contact at PIM X1 connector. If PIM X1 terminal contact tests OK, perform the

Intermittent Condition Testing below.

3. Disconnect the transmission X176 24-way connector.

4. Connect the DT-48493 to the X176 24-way connector at the transmission.

5. Using the Position Sensor Specification table specifications listed below, test the position sensor resistance at the transmission X176 circuits

as indicated. Also test each circuit for a short to ground.

瀚慖f all circuits test normal, continue with testing.

瀚慖f any of the circuits are not within specification, test the internal transmission harness for the condition. If the internal transmission

harness tests OK, replace the applicable drive motor generator.

6. Disconnect DT-48493 from the transmission X176 24-way connector.

7. Connect the DT-48493 to the transmission X176 24-way connector at the vehicle harness.

8. Disconnect PIM X1 connector.

9. Using the PIM to Transmission Terminal Reference table listed below, test the vehicle harness continuity between PIM X1 connector and

transmission X176. Also test these circuits for short to ground and to the shield circuit if the shield circuit is not presently grounded to the

PIM assembly.

瀚慖f any of the circuits are not within the specified range, repair or replace the wiring harness.

瀚慖f all circuits test normal, inspect transmission connector X176 for proper terminal contact. If transmission connector X176 tests OK,

inspect the harness for an intermittent concern.

Intermittent Condition Testing

1. If possible, determine which of the position sensor circuits have the intermittent condition by reviewing the Diagnostic Fault Information

table. For example, DTCs P0C57 and P0C52 only set for a short to ground condition on either the S1 or S3 circuit.

2. Using the Position Sensor Specification table listed below, monitor the position sensor circuits at PIM X1 connector while manipulating the

applicable harness and connectors.

瀚慖f any of the circuits are not within specification, repair the harness or terminal as required. If a harness repair is indicated and external

harness damage is not evident, the most likely location for internal wire damage is near the harness clamping locations.

3. Disconnect transmission X176 connector and inspect for the following:

* Proper terminal contact