1-800-424-9153), or go to http://www.safercar.gov.2010 Cadillac Truck SRX AWD V6-3.0L Technical Service Bulletin # 10-08-45-002D Date: 100913
Electrical - Malfunction Indicator Lamp ON/Hard/No Start
TECHNICAL
Bulletin No.: 10-08-45-002D
Date: September 13, 2010
Subject: Malfunction Indicator Lamp (MIL) Illuminated, Hard/No Start, Water on Driver Front Floor, DTCs Set (Replace Inline Pass-Thru
Connector and Fuel Tank Wiring Harness as Needed)
Models:
2010 Cadillac SRX
Supercede:
This bulletin is being revised to add DTC information. Please discard Corporate Bulletin Number 10-08-45-002C (Section 08 - Body and
Accessories).
Condition
Some customers may comment on one or more of the following conditions:
- The engine is hard to start or will not start, due to low fuel pressure.
- Erratic fuel gauge operation.
- The malfunction indicator lamp (MIL) is illuminated.
- There is a water leak in the driver side front floor area.
Upon further investigation, one or more of the following DTCs may be set:
Evaporative Emissions System
- DTC P0442: Evaporative Emission System Small Leak Detected
- DTC P0446: Evaporative Emissions Vent System Performance
- DTC P0449: Evaporative Emission (EVAP) Vent Solenoid Control Circuit
- DTC P0455: Evaporative Emission System Large Leak Detected
- DTC P0496: Evaporative Emission (EVAP) System Flow During Non-Purge
- DTC P0497: Evaporative Emission (EVAP) System No Flow During Purge
- DTC P0498: Evaporative Emission (EVAP) Vent Solenoid Valve Control Circuit Low Voltage
- DTC P0499: Evaporative Emission (EVAP) Vent Solenoid Valve Control Circuit High Voltage
Fuel Tank Pressure Sensor
- DTC P0451: Fuel Tank Pressure Sensor Performance
- DTC P0452: Fuel Tank Pressure Sensor Circuit Low Voltage
- DTC P0453: Fuel Tank Pressure Sensor Circuit High Voltage
2010 Cadillac Truck SRX AWD V6-3.0L Page 241
- DTC P0454: Fuel Tank Pressure Sensor Intermittent
Fuel Pressure/Fuel Rail Pressure Sensor
- DTC P018B: Fuel Pressure Sensor Performance
- DTC P018C: Fuel Pressure Sensor Circuit Low Voltage
- DTC P018D: Fuel Pressure Sensor Circuit High Voltage
- DTC P0191: Fuel Rail Pressure Sensor Performance
- DTC P0192: Fuel Rail Pressure Sensor Circuit Low Voltage
- DTC P0193: Fuel Rail Pressure Sensor Circuit High Voltage
Cause
These conditions may be caused by water leaking into the vehicle causing terminal corrosion at inline connector X 350. This connector is not sealed
off from the inside of the vehicle and if a leak is present, water may eventually enter the connector causing the terminals to become corroded.
Correction
1. Disconnect the separate fuel tank harness connectors that connect to the underside of the X 350 connector. For the location of X 350, refer to
> Power and Signal Distribution > Wiring Systems and Power Management > Component Locator > Master Electrical Component List >
Code > X 350 in SI.
2. Inspect the terminals of these connectors for any corrosion, intermittent conditions and poor connections. Refer to testing for Intermittent
Conditions and Poor Connections in SI.
瀚慖f the terminals show any sign of corrosion, determine the source of the water leak. Repair the leak as necessary, Refer to > General
Information > Water Leaks > Diagnostic Information and Procedures in SI.
3. Replace the fuel tank harness to body harness pass-thru CONNECTOR with the new SEALED DESIGN CONNECTOR P/N 19178098.
4. Replace the connector terminals with terminals P/N 12047581 and P/N 12034047 found in the J 38125 Terminal Repair Kit. Refer to >
Power and Signal Distribution > Wiring Systems and Power Management > Diagnostic Information and Procedures in SI.
5. Inspect the mating fuel tank wiring harness connector terminals for any sign of corrosion.
瀚慖f the mating fuel tank wiring harness connector terminals show any sign of corrosion, replace the wiring harness.
Parts Information
Warranty Information
For vehicles repaired under warranty, use the appropriate labor operation for the repair that was performed:.
