2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 622
B2540 05
The BCM detects a short to voltage or an open/high resistance in the rear fog lamp switch signal circuit.
Action Taken When the DTC Sets
The rear fog lamps will not operate when the park lamps are ON and the rear fog lamp switch is active.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Fog Lights Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System Diagram/Fog Lights Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the headlamp switch.
2. Verify that a test lamp illuminates between B+ and the ground circuit terminal 8.
瀚慖f the test lamp does not illuminate, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Rear Fog Lamp Switch parameter is INACTIVE.
瀚慖f not the specified value, test the signal circuit terminal 6 for a short to ground. If the circuit tests normal, replace the XBCM.
4. Install a 3 A fused jumper wire between the signal circuit terminal 6 and ground. Verify the scan tool Rear Fog Lamp Switch parameter is
ACTIVE.
瀚慖f not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the
XBCM.
5. If all circuits test normal, test or replace the headlamp switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Headlamp Switch Replacement (Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service and Repair/Headlamp Switch
Replacement (Cadillac)) Headlamp Switch Replacement (Except Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service
and Repair/Headlamp Switch Replacement (Except Cadillac))
* Control Module References (See: Testing and Inspection/Programming and Relearning) for XBCM replacement, setup, and programming
Diagnostic Repair parts ,Wiring Diagrams. DTC. TSB,Car, Truck, SUV & Van Acura Chrysler Infiniti Maserati Rolls-Royce Alfa Romeo Dodge Jaguar Mazda Scion Aston Martin Ferrari Jeep McLaren Smart Audi Fiat Karma Mercedes-Benz Spyker BMW Ford Kia Mini Subaru Bentley Freightliner Lamborghini Mitsubishi Tesla Bugatti GMC Land Rover Mobility Ventures Toyota Buick Genesis Lexus Nissan Volkswagen Cadillac Honda Lincoln Porsche Volvo Chevrolet Hyundai Lotus Ram