Monday, January 20, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1053

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1053



* Before the ECM can report DTC P0111 failed, DTC P0101 must run and pass.



* DTC P0112, P0113, P0116, P0117, P0118, P0119, or P0128 is not set.



* The ECT at engine start is colder than 120掳C (248掳F).



* The ECT is warmer than 75掳C (167掳F).



* The vehicle speed is greater than 40 km/h (25 mph).



* The MAF is between 15.6 and 250 g/s.



* Decel fuel cut-off is not active.



* DTC P0111 runs continuously when the above conditions are met for greater than 2 s.



P0111 Rationality Test



* The ECT at engine start is warmer than 35掳C (95掳F).



* The ECT at last engine shut down was warmer than 80掳C (176掳F).



* Since last shut down, the ECT has decreased more than 40掳C (69掳F).



* DTC P0111 runs continuously when the above conditions are met for greater than 20 s.



P0112 and P0113



* The engine run time is greater than 15 s.



* The engine is idling for greater than 3 s.



* The IAT is colder than 35掳C (95掳F).



* The IAT change is more than 2.3掳C (4.1掳F).



* The DTCs runs continuously when the above conditions are met fro greater than 2 s.



P0114



* The ignition is ON.



* The DTCs runs continuously within the enabling conditions.



Conditions for Setting the DTC



P0111



* The ECM detects that the IAT remains steady within 2掳C (4掳F) during the idle test.



* The ECM detects that the IAT decreased less than 2掳C (4掳F) during the cruise test.



* Any of the above conditions exists for greater than a cumulative of 45 s for the cruse test or 55 s for the idle test.



* The ECM detects that the difference between the IAT and the ECT less than -20掳C (-36掳F) OR more than 35掳C (63掳F).



* The above condition exists for greater than 2 s.



P0112



The ECM detects that the intake air temperature is warmer than 132掳C (270掳F) for greater than 4 s or a cumulative of 30 s.



P0113



The ECM detects that the intake air temperature is colder than -42掳C (-43.6掳F) and remains steady within 3掳C (5掳F) during a cumulative air flow of



greater than 999 grams. The scan tool is limited to -40掳C (-40掳F), so the diagnostic procedure uses -39掳C (-38掳F) to determine if there is an IAT



condition. The condition exists for greater than 4 s or a cumulative of 30 s.



P0114



The ECM detects that the IAT sensor signal is intermittent or has abruptly changed for period of time greater than 5 s.



Action Taken When the DTC Sets



DTCs P0111, P0112, P0113, and P0114 are Type B DTCs.



Conditions for Clearing the MIL/DTC



DTCs P0111, P0112, P0113, and P0114 are Type B DTCs.



Diagnostic Aids



* If the vehicle has sat overnight, the IAT sensor and the ECT sensor values should be within 3掳C (5掳F).



* High resistance on the IAT sensor signal circuit could set a DTC.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)