Tuesday, January 28, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1536

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1536



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Special Tools



J 35616 - Connector Test Adapter Kit



Circuit/System Verification



Note: If you were sent here from Engine Cranks But Does Not Run proceed to Circuit/System Testing.



1. Engine running, command the Engine Controls (EC) Ignition Relay ON and OFF with a scan tool while observing the following EC Ignition



Relay control circuit status parameters:



* Engine Controls Ignition Relay Control Circuit Low Voltage Test Status



* Engine Controls Ignition Relay Control Circuit Open Test Status



* Engine Controls Ignition Relay Control Circuit High Voltage Test Status



Each parameter should display OK or Not Run.



2. Ignition ON, you should be able to communicate with the ECM using a scan tool.



3. Ignition ON, view the DTC information with a scan tool. DTC P0685, P0686, P0687, P0689, or P0690 should not set.



4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, disconnect the KR75 powertrain relay.



2. Ignition ON, verify a test lamp illuminates between both of the following relay battery voltage circuit terminals and ground.



* Terminal 86



* Terminal 87



瀚慖f the test lamp does not illuminate, test the relay battery voltage circuit for a short to ground or an open/high resistance.



Note: The ignition voltage circuit is between the powertrain relay and the ECM. The ignition voltage circuit is a feedback circuit.



3. Ignition OFF, verify that a test lamp does not illuminate between the ignition voltage circuit terminal 30 and ground.



瀚慖f the test lamp illuminates, test the ignition voltage circuit for a short to voltage.



4. Connect a 20 A fused jumper wire between the relay switch B+ circuit terminal 87 and the relay switch ignition voltage circuit terminal 30.



5. Ignition ON, observe the scan tool EC Ignition Relay Feedback Signal parameter. The ECM should communicate, and the parameter should



display 9-14 V.



瀚慖f not the specified range, or the ECM does not communicate, test the ignition voltage circuit between the powertrain relay and the ECM



for a short to ground or for an open/high resistance. If the circuit/connections test normal, replace the K20 ECM.



6. Ignition OFF, verify that a test lamp does not illuminate between the control circuit terminal 85 and B+.



瀚慖f the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.



7. Connect a DMM set to the diode setting between the control circuit terminal 85 and ground.



8. Ignition ON, verify the DMM does not display OL.



瀚慖f the DMM displays OL, test the control circuit for a short to voltage, or an open/high resistance. If the circuit tests normal, replace the



K20 ECM.



9. If all circuits test normal, replace the KR75 powertrain relay.