2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2775
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures must
be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Perform the High Voltage Disabling () procedure.
2. Ignition OFF, disconnect harness connector X1 of the BECM.
3. Reconnect the 12-volt battery.
4. Ignition OFF and scan tool disconnected, test for less than 1 volt between wake up signal terminal 13 and ground.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming
U0210
DTC U0100-U02FF (without HP2)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
Refer to Control Module U Code List (See: Diagnostic Trouble Code Descriptions/Control Module U Code List).
Diagnostic Fault Information
Circuit/System Description
The serial data circuit is the means by which the control modules in the vehicle communicate with each other. Once the scan tool is connected to the
serial data circuit through the DLC, the scan tool can be used to monitor each control module for diagnostic purposes and to check for diagnostic
trouble codes (DTCs). When the ignition switch is in RUN, each control module communicating on the serial data circuit sends a state of health
(SOH) message to ensure that the control module is operating properly. When a control module stops communicating on the serial data circuit, for
example if the module loses power or ground, the SOH message it normally sends on the serial data circuit disappears. Other control modules on
the serial data circuit, which expect to receive that SOH message, detect its absence; those control modules in turn set a DTC associated with the
loss of SOH of the non-communicating control module. The DTC is unique to the control module which is not communicating and one or more
control modules may set the same exact code. A loss of serial data communications DTC does not represent a failure of the control modules that
contain the stored code.
Showing posts with label * Identify how to disable high voltage.. Show all posts
Showing posts with label * Identify how to disable high voltage.. Show all posts
Saturday, December 12, 2020
Friday, November 8, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1424
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1424
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B60
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B60
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
Thursday, November 7, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1363
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1363
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B7D
DTC P0B3C, P0B41, P0B46, P0B4B, P0B50, P0B55, P0B5A, P0B5F, P0B64, P0B69, P0B6E, P0B73, P0B78, P0B7D, P0B82, P0B87, P0B8C,
P0B91, P0B96, or P0B9B
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3C
- Hybrid Battery 1 Circuit Performance
DTC P0B41
- Hybrid Battery 2 Circuit Performance
DTC P0B46
- Hybrid Battery 3 Circuit Performance
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B7D
DTC P0B3C, P0B41, P0B46, P0B4B, P0B50, P0B55, P0B5A, P0B5F, P0B64, P0B69, P0B6E, P0B73, P0B78, P0B7D, P0B82, P0B87, P0B8C,
P0B91, P0B96, or P0B9B
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3C
- Hybrid Battery 1 Circuit Performance
DTC P0B41
- Hybrid Battery 2 Circuit Performance
DTC P0B46
- Hybrid Battery 3 Circuit Performance
Wednesday, October 30, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1661
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1661
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures must
be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the air conditioning control module terminal X4 B+ (300 V) and terminal X5 ground (300 V).
3. Test for infinite resistance between the terminals listed below and ground;
* X4 B+ (300 V) cable
* X5 ground (300 V) cable
锟斤拷If less than the specified value, replace the air conditioning control module assembly.
4. Test for greater than 50k ohm between the B+ (300 V) terminals X4 and ground (300 V) X5.
锟斤拷If less than the specified range, test the circuits for a short between the circuits. If the circuits test normal, replace the air conditioning
control module assembly.
5. Connect the EL-48458 at the drive motor generator power inverter module. Refer to the EL-48458 installation procedure located in High
Voltage System Diagnosis (EL-48458) ().
Note: Install a manual disconnect lever with a verified good fuse or a new manual disconnect lever.
6. Install the manual disconnect lever.
7. Connect the 12 V battery.
8. Ignition ON, attempt to precharge the high voltage system by moving the high voltage contactor relay switch on the tester to the closed
position. Verify that the hi-voltage greater than 60 V LED does not illuminate.
锟斤拷If the LED illuminates, replace the drive motor generator power inverter module.
Note: The following tests require wearing personal protection equipment (PPE) gloves.
9. Ignition OFF, remove the EL-48458. Refer to the removal procedure located in High Voltage System Diagnosis (EL-48458) ().
10. Ignition OFF, disconnect the X1 B+ (300 V) and X2 ground (300 V) cables from the drive motor generator battery.
11. Test for infinite resistance between the terminals listed below and ground
* X1 B+ (300 V) cable
* X2 ground (300 V) cable
锟斤拷If less than the specified value, replace the high voltage cables.
12. Ignition ON, command the negative and positive contactors and the current limit relay ON and OFF with a scan tool. Listen for the contactors
and relay to turn ON and OFF.
锟斤拷If the negative contactor, positive contactor or the current limit relay does not turn ON and OFF, refer to High Voltage Contactor/Relay
Malfunction ().
13. Ignition OFF, visually inspect and test the drive motor generator battery internal high voltage DC cables and connections for a short to
ground or an open/high resistance condition.
锟斤拷If a short to ground or an open/high resistance condition is found on the high voltage cables or connection points, replace the drive motor
generator battery cable.
14. If all the circuit tests normal, replace the drive motor generator battery assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Battery Negative Relay Cable Replacement ()
* Drive Motor Battery Positive Relay Cable Replacement ()
* Drive Motor Battery Positive and Negative Cable Replacement ()
* Drive Motor Battery 300-Volt Positive and Negative Cable Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module,
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures must
be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the air conditioning control module terminal X4 B+ (300 V) and terminal X5 ground (300 V).
3. Test for infinite resistance between the terminals listed below and ground;
* X4 B+ (300 V) cable
* X5 ground (300 V) cable
锟斤拷If less than the specified value, replace the air conditioning control module assembly.
4. Test for greater than 50k ohm between the B+ (300 V) terminals X4 and ground (300 V) X5.
锟斤拷If less than the specified range, test the circuits for a short between the circuits. If the circuits test normal, replace the air conditioning
control module assembly.
5. Connect the EL-48458 at the drive motor generator power inverter module. Refer to the EL-48458 installation procedure located in High
Voltage System Diagnosis (EL-48458) ().
Note: Install a manual disconnect lever with a verified good fuse or a new manual disconnect lever.
6. Install the manual disconnect lever.
7. Connect the 12 V battery.
8. Ignition ON, attempt to precharge the high voltage system by moving the high voltage contactor relay switch on the tester to the closed
position. Verify that the hi-voltage greater than 60 V LED does not illuminate.
锟斤拷If the LED illuminates, replace the drive motor generator power inverter module.
Note: The following tests require wearing personal protection equipment (PPE) gloves.
9. Ignition OFF, remove the EL-48458. Refer to the removal procedure located in High Voltage System Diagnosis (EL-48458) ().
10. Ignition OFF, disconnect the X1 B+ (300 V) and X2 ground (300 V) cables from the drive motor generator battery.
11. Test for infinite resistance between the terminals listed below and ground
* X1 B+ (300 V) cable
* X2 ground (300 V) cable
锟斤拷If less than the specified value, replace the high voltage cables.
12. Ignition ON, command the negative and positive contactors and the current limit relay ON and OFF with a scan tool. Listen for the contactors
and relay to turn ON and OFF.
锟斤拷If the negative contactor, positive contactor or the current limit relay does not turn ON and OFF, refer to High Voltage Contactor/Relay
Malfunction ().
13. Ignition OFF, visually inspect and test the drive motor generator battery internal high voltage DC cables and connections for a short to
ground or an open/high resistance condition.
锟斤拷If a short to ground or an open/high resistance condition is found on the high voltage cables or connection points, replace the drive motor
generator battery cable.
14. If all the circuit tests normal, replace the drive motor generator battery assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Battery Negative Relay Cable Replacement ()
* Drive Motor Battery Positive Relay Cable Replacement ()
* Drive Motor Battery Positive and Negative Cable Replacement ()
* Drive Motor Battery 300-Volt Positive and Negative Cable Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module,
Monday, October 28, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1424
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1424
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B60
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B60
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
Sunday, October 27, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1363
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1363
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B7D
DTC P0B3C, P0B41, P0B46, P0B4B, P0B50, P0B55, P0B5A, P0B5F, P0B64, P0B69, P0B6E, P0B73, P0B78, P0B7D, P0B82, P0B87, P0B8C,
P0B91, P0B96, or P0B9B
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3C
- Hybrid Battery 1 Circuit Performance
DTC P0B41
- Hybrid Battery 2 Circuit Performance
DTC P0B46
- Hybrid Battery 3 Circuit Performance
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B7D
DTC P0B3C, P0B41, P0B46, P0B4B, P0B50, P0B55, P0B5A, P0B5F, P0B64, P0B69, P0B6E, P0B73, P0B78, P0B7D, P0B82, P0B87, P0B8C,
P0B91, P0B96, or P0B9B
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3C
- Hybrid Battery 1 Circuit Performance
DTC P0B41
- Hybrid Battery 2 Circuit Performance
DTC P0B46
- Hybrid Battery 3 Circuit Performance
Subscribe to:
Posts (Atom)