2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2354
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.
Circuit/System Verification
1. Engine ON, verify the transmission fluid temperature is between 50-80掳C (122-176掳F).
2. Operate the vehicle long enough to verify at least a 3掳C (5掳F) rise in TCM temperature parameter, then operate the vehicle in Park for 5
seconds.
3. Engine ON, observe the scan tool Line PC Sol. CKT Status parameter. The reading should display OK or Indeterminate.
瀚慖f the reading is not within the specified range, replace the control solenoid valve assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control
Solenoid Valve and Transmission Control Module Assembly Inspection) for control solenoid inspection.
* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,
setup, and programming.
6L50/6L80/6L90 - Automatic Transmission
DTC P0961-P0963
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0961
- Line Pressure Control (PC) Solenoid System Performance
DTC P0962
- Line Pressure Control (PC) Solenoid Control Circuit Low Voltage
DTC P0963
- Line Pressure Control (PC) Solenoid Control Circuit High Voltage
Diagnostic Fault Information
Showing posts with label Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams). Show all posts
Showing posts with label Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams). Show all posts
Wednesday, November 25, 2020
Friday, November 20, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2252
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2252
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Special Tools
J 24731 Tempil Stick
Circuit/System Verification
Ignition ON, observe the scan tool Trans. Fluid Temp. and the TCM temperature parameters. The readings should vary less than 10掳C (18掳F).
If within the specified range, test for a transmission overheat condition.
If greater than the specified range, replace the Q8 control solenoid valve assembly.
Component Testing
* Perform the Fluid Leak Diagnosis (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component
Tests and General Diagnostics/2ML70 - Automatic Transmission/Fluid Leak Diagnosis).
* Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing
and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Transmission Fluid Level and Condition Check)
procedure.
* Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component
Tests and General Diagnostics/2ML70 - Automatic Transmission/Line Pressure Check) procedure.
* Perform the Main Fluid Pump Pressure High or Low (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Main Fluid Pump Pressure High or Low) procedure.
* With a hand held infra red thermometer, or J 24731 test for the transmission cooler supply line thermostat for opening at 80掳C (176掳F). The
transmission cooler supply line temperature should be higher on the transmission side of the thermostat than the cooler side until 80掳C (176掳
F) is reached.
瀚慖f the thermostat tests stuck open or closed, replace the transmission cooler supply pipe assembly.
Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid
Valve and Transmission Control Module Assembly Inspection).
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Transmission Fluid Cooler Pipe Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Fluid
Line/Hose/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for Q8 control solenoid valve assembly
replacement, setup, and programming.
P0713
DTC P0711, P0712, or P0713
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Special Tools
J 24731 Tempil Stick
Circuit/System Verification
Ignition ON, observe the scan tool Trans. Fluid Temp. and the TCM temperature parameters. The readings should vary less than 10掳C (18掳F).
If within the specified range, test for a transmission overheat condition.
If greater than the specified range, replace the Q8 control solenoid valve assembly.
Component Testing
* Perform the Fluid Leak Diagnosis (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component
Tests and General Diagnostics/2ML70 - Automatic Transmission/Fluid Leak Diagnosis).
* Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing
and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Transmission Fluid Level and Condition Check)
procedure.
* Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component
Tests and General Diagnostics/2ML70 - Automatic Transmission/Line Pressure Check) procedure.
* Perform the Main Fluid Pump Pressure High or Low (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Main Fluid Pump Pressure High or Low) procedure.
* With a hand held infra red thermometer, or J 24731 test for the transmission cooler supply line thermostat for opening at 80掳C (176掳F). The
transmission cooler supply line temperature should be higher on the transmission side of the thermostat than the cooler side until 80掳C (176掳
F) is reached.
瀚慖f the thermostat tests stuck open or closed, replace the transmission cooler supply pipe assembly.
Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid
Valve and Transmission Control Module Assembly Inspection).
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Transmission Fluid Cooler Pipe Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Fluid
Line/Hose/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for Q8 control solenoid valve assembly
replacement, setup, and programming.
P0713
DTC P0711, P0712, or P0713
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Tuesday, November 17, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2160
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2160
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
Verify that DTC P0601, P0602, P0603, P0604, P0606, P060B, or P062F is not set.
If the DTC is set, program the Q8 control solenoid valve assembly. If the DTC resets, replace the Q8 control solenoid valve assembly.
Component Testing
Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid
Valve and Transmission Control Module Assembly Inspection).
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,
and programming.
6L45/6L50/6L80/6L90 - Automatic Transmission
DTC P0601-P0604 or P062F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
Note: DTCs P0601, P0602, P0603, P0604 or P062F could set in other control modules. Verify the DTCs are set in the transmission control module
(TCM).
DTC P0601
- Control Module Read Only Memory (ROM)
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory (RAM)
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
Verify that DTC P0601, P0602, P0603, P0604, P0606, P060B, or P062F is not set.
If the DTC is set, program the Q8 control solenoid valve assembly. If the DTC resets, replace the Q8 control solenoid valve assembly.
Component Testing
Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid
Valve and Transmission Control Module Assembly Inspection).
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,
and programming.
6L45/6L50/6L80/6L90 - Automatic Transmission
DTC P0601-P0604 or P062F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
Note: DTCs P0601, P0602, P0603, P0604 or P062F could set in other control modules. Verify the DTCs are set in the transmission control module
(TCM).
DTC P0601
- Control Module Read Only Memory (ROM)
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory (RAM)
Wednesday, January 22, 2020
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1671
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1671
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
* Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
* Inline Harness Connector End Views (See: Diagrams/Connector Views/Multiple Junction Connector/Connector End Views By Number)
Description and Operation
Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/6T70/6T75 -
Automatic Transmission/Electronic Component Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
DT-47825-20 Adapter Harness
Circuit/System Verification
1. If there are any other transmission DTCs set, diagnose those DTCs first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See:
Diagnostic Trouble Code Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Perform the Range Selector Lever Cable Adjustment (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Shift
Linkage/Shift Cable/Adjustments) procedure to verify proper adjustment.
3. Ignition ON, observe the scan tool ECM PNP Switch parameter while moving the gear shift lever from Park and through all ranges. The
parameter should display Park/Neutral when in Park or Neutral and In-Gear when in Reverse or Drive.
4. Observe the scan tool TCM IMS A/B/C/P parameter while slowly moving the gear shift lever from Park through all ranges. The parameter
should match each gear range that is selected. Refer to Transmission Internal Mode Switch Logic (See: Specifications/Mechanical
Specifications/Automatic Transmission/Transaxle/System Specifications/6T70/6T75 - Automatic Transmission/Transmission Internal Mode
Switch Logic).
5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Note: You must perform the Circuit/System Verification first.
1. Ignition OFF, disconnect the 20-way harness connector at the transmission.
2. Install the DT-47825-20 to the 20-way harness connector to the engine harness.
3. Test for less than 10 ohms between the ground circuit terminal 18 and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
4. Ignition ON, verify the scan tool ECM PNP Switch parameter displays In Gear.
瀚慖f not the specified value, test the P/N signal circuit for a short to ground. If the circuit tests normal, replace the engine control module.
5. Connect a 3-amp fused jumper wire between the TCM harness connector terminal 3 and terminal 18. Verify the PNP Switch parameter
changes to Park/Neutral.
瀚慖f not the specified value, test the P/N signal circuit for an open/high resistance. If the circuit tests normal, replace the engine control
module.
6. Ignition OFF, remove the control valve body cover. Refer to Control Valve Body Cover Replacement (See: Transmission and
Drivetrain/Automatic Transmission/Transaxle/Valve Body/Service and Repair/6T70/6T75 - Automatic Transmission/Control Valve Body
Subscribe to:
Posts (Atom)