2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999

P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and

P2176 are not set.

* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.

* Engine run time is more than 2 crankshaft revolutions.

* The engine speed is between 375-5,600 RPM.

* The ignition voltage is between 9-18 volts.

* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).

* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).

* The fuel level is more than 10 percent.

* The ECM is not in fuel shut-off, or decel fuel cut-off mode.

* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.

* An automatic transmission shift with a throttle position more than 95 percent is not occuring.

* The power management is not active.

* Excessive drive wheel slip is not detected.

* The power take-off (PTO) is disabled, where applicable.

* The cylinder deactivation is not in progress, where applicable.

* DTCs P0300-P0308 run continuously when the above conditions are met.

Conditions for Setting the DTC

DTC P0300

The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at

catalytic converter damaging levels.

DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308

The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or

is at catalytic converter damaging levels.

Action Taken When the DTC Sets

* DTCs P0300-P0308 are Type B DTCs.

* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.

* Depending on the conditions that set the DTC, the engine may go into Open Loop.

Conditions for Clearing the MIL/DTC

* DTCs P0300-P0308 are Type B DTCs.

* The DTC must run and pass under the same operating conditions that were present when the DTC failed.

Diagnostic Aids

* Ensure that each fuel injector is connected to the proper fuel injector harness connector.

* A misfire may only occur when the engine is operating under a load or when the engine is cold.

* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC

circuit P0351-P0358 DTC.

* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:

Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of

vibration:

- A tire or wheel that is out of round or balance

- Variable thickness brake rotors

- An unbalanced drive shaft

- Certain rough road conditions

- A damaged accessory drive component or belt

- A damaged reluctor wheel

- The Crankshaft Position System Variation Learn procedure may need to be performed.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1552

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1552

1. Ignition ON, observe the DTC information with a scan tool. DTC P0641, P0642, P0643, P0651, P0652, P0653, P0697, P0698, or P0699

should not set.

2. Observe the appropriate scan tool 5 V Reference 1, 2, or 3 Circuit Status parameter. The parameter should display OK.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: Additional DTCs will set when disconnecting the components.

1. Ignition OFF, disconnect the harness connector of all appropriate sensors for the applicable DTC. Refer to Diagnostic Aids.

2. Ignition ON, test for 4.8-5.2 V between one of the affected 5 V reference circuits and ground.

瀚慖f the voltage is less than the specified range, test for a short to ground on the 5 V reference circuit for each of the affected components. If

all circuits test normal, replace the K20 ECM.

瀚慖f the voltage is greater than the specified range, test for a short to voltage on the 5 V reference circuit for each of the affected

components. If all circuits test normal, replace the K20 ECM.

Note: A short to voltage on the signal circuit of certain components may cause this DTC to set.

3. Connect each component associated with the affected 5 V reference circuit one at a time while monitoring the appropriate scan tool 5 V

Reference Circuit Voltage parameter. Verify the voltage remains between 4.8-5.2 V.

瀚慖f not within the specified range when a component is connected, test the signal circuit of that component for a short to voltage. If the

circuit tests normal, replace the component.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Accelerator Pedal with Position Sensor Assembly Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Accelerator

Pedal/Service and Repair/Accelerator Pedal with Position Sensor Assembly Replacement)

* Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement (LF1) (See: Heating and Air Conditioning/Refrigerant Pressure Sensor /

Switch/Service and Repair)Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement (LAU) (See: Heating and Air

Conditioning/Refrigerant Pressure Sensor / Switch/Service and Repair)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)

* Crankshaft Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Crankshaft Position

Sensor/Service and Repair)

* Fuel Injector Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Service and Repair)

* Fuel Tank Pressure Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Fuel Tank Pressure Sensor/Service

and Repair)

* Secondary Injection Shutoff Valve Pressure Sensor Replacement (See: Powertrain Management/Emission Control Systems/Air Injection/Air

Injection Check Valve/Service and Repair)

* Throttle Body Assembly Replacement (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Throttle Body/Service and

Repair/Removal and Replacement)Throttle Body Assembly Replacement (LAU) (See: Powertrain Management/Fuel Delivery and Air

Induction/Throttle Body/Service and Repair/Removal and Replacement)

* Turbocharger Pressure Sensor Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Turbocharger/Service and

Repair/Turbocharger Pressure Sensor Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0699

DTC P0641-P0643, P0651-P0653, or P0697-P0699 (ECM, LAU)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.