2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1873

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1873

(w/body and TCM) valve assembly. Inspect the IMS, harness, connector, and control solenoid (w/body and TCM) valve assembly pins for metallic

debris. Use a terminal test kit for any test that requires probing the control solenoid (w/body and TCM) valve assembly harness connector or a

component harness connector. The IMS assembly can be damaged by currents exceeding 2 mA. Test the IMS assembly for an open condition

whenever a short to voltage condition is observed.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.

Circuit/System Verification

Test for the correct operation of the IMS. Refer to Transmission Internal Mode Switch Logic (See: Specifications/Mechanical

Specifications/Automatic Transmission/Transaxle/System Specifications/2ML70 - Automatic Transmission/Transmission Internal Mode Switch

Logic).

If the IMS operation matches the IMS logic table, the system if functioning normally.

Circuit/System Testing

1. Disconnect the IMS harness connector at the control solenoid (w/body and TCM) valve assembly. Ignition ON. The scan tool IMS A/B/C/P

parameter should display HI for all 4 signal circuits.

瀚慖f a signal circuit displays LOW, replace the control solenoid (w/body and TCM) valve assembly.

2. Connect a 3-amp fused jumper wire between each transmission range signal circuit at the control solenoid (w/body and TCM) valve assembly

and ground. With a scan tool, ensure that each signal circuit displays LOW when connected to ground.

瀚慖f a signal circuit remains HI when connected to ground, replace the control solenoid (w/body and TCM) valve assembly.

3. Connect the IMS harness connector to the control solenoid (w/body and TCM) valve assembly. Disconnect the IMS connector. The scan tool

IMS A/B/C/P parameter should display HI for all 4 signal circuits.

瀚慖f a signal circuit displays LOW, replace the IMS jumper harness.

4. Connect a 3-amp fused jumper wire between each transmission range signal circuit at the IMS connector harness and ground. With a scan

tool, ensure that each signal circuit displays LOW when connected to ground.

瀚慖f a signal circuit remains HI when connected to ground, replace the IMS harness.

瀚慖f a signal circuit other than the circuit being grounded displays LOW, replace the IMS harness.

瀚慖f all circuits test normal, replace the IMS.

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1974

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1974

(w/body and TCM) valve assembly. Inspect the IMS, harness, connector, and control solenoid (w/body and TCM) valve assembly pins for metallic

debris. Use a terminal test kit for any test that requires probing the control solenoid (w/body and TCM) valve assembly harness connector or a

component harness connector. The IMS assembly can be damaged by currents exceeding 2 mA. Test the IMS assembly for an open condition

whenever a short to voltage condition is observed.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.

Circuit/System Verification

Test for the correct operation of the IMS. Refer to Transmission Internal Mode Switch Logic (See: Specifications/Mechanical

Specifications/Automatic Transmission/Transaxle/System Specifications/2ML70 - Automatic Transmission/Transmission Internal Mode Switch

Logic).

If the IMS operation matches the IMS logic table, the system if functioning normally.

Circuit/System Testing

1. Disconnect the IMS harness connector at the control solenoid (w/body and TCM) valve assembly. Ignition ON. The scan tool IMS A/B/C/P

parameter should display HI for all 4 signal circuits.

锟斤拷If a signal circuit displays LOW, replace the control solenoid (w/body and TCM) valve assembly.

2. Connect a 3-amp fused jumper wire between each transmission range signal circuit at the control solenoid (w/body and TCM) valve assembly

and ground. With a scan tool, ensure that each signal circuit displays LOW when connected to ground.

锟斤拷If a signal circuit remains HI when connected to ground, replace the control solenoid (w/body and TCM) valve assembly.

3. Connect the IMS harness connector to the control solenoid (w/body and TCM) valve assembly. Disconnect the IMS connector. The scan tool

IMS A/B/C/P parameter should display HI for all 4 signal circuits.

锟斤拷If a signal circuit displays LOW, replace the IMS jumper harness.

4. Connect a 3-amp fused jumper wire between each transmission range signal circuit at the IMS connector harness and ground. With a scan

tool, ensure that each signal circuit displays LOW when connected to ground.

锟斤拷If a signal circuit remains HI when connected to ground, replace the IMS harness.

锟斤拷If a signal circuit other than the circuit being grounded displays LOW, replace the IMS harness.

锟斤拷If all circuits test normal, replace the IMS.