2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1735
uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases toward 1,000 mV indicates a rich fuel mixture. An HO2S
voltage that decreases toward 0 mV indicates a lean fuel mixture.
The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed
Loop earlier and the control module to calculate the air-to-fuel ratio sooner.
Conditions for Running the DTC
P0133, P0153, P1133, or P1153
* DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128,
P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516,
P2101, P2119, P2135, P2176 are not set.
* The engine coolant temperature (ECT) is greater than 60锟斤拷C (140锟斤拷F).
* The intake air temperature (IAT) is warmer than -40锟斤拷C (-40锟斤拷F)
* The ignition 1 voltage is between 10-32 V.
* The fuel level is greater than 10 %.
* The engine run time is greater than 160 s.
* The engine speed is between 1,200-3,000 RPM.
* The barometric (BARO) pressure is greater than 70 kPa.
* The mass airflow (MAF) is between 20-55 g/s.
* The fuel system is in Closed Loop.
* The throttle position (TP) is greater than 5 %.
* The DTCs run once per drive cycle when the above conditions are met.
P013A P013C, P013E, or P014A
* Before the ECM can report DTC P013A, or P013C failed, DTCs P013E, P014A, P2270, and P2272 must run and pass.
* Before the ECM can report DTC P013E, or P014A failed, DTCs P2270 and P2272 must run and pass.
* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The accelerator pedal (APP) is steady.
* The torque converter clutch (TCC) is applied.
* The DTCs run once per ignition cycle, during decel fuel cut-off (DFCO), when the above conditions are met.
P013B P013D, P013F, or P014B
* Before the ECM can report DTC P013B, or P013D failed, DTCs P013A, P013C, P013E, P013F, P014A, P014B, P2270, P2271, P2272, and
P2273 must run and pass.
* Before the ECM can report DTC P013F, or P014B failed, DTCs P013A, P013C, P013E, P014A, P2270, P2271, P2272, and P2273 must run
and pass.
* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
