2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1681
Conditions for Setting the DTC
The MCM cannot track the motor position.
Action Taken When the DTC Sets
* DTCs P1B03 and P1B04 are Type A DTCs.
* The hybrid powertrain control module (HPCM) commands the battery energy control module (BECM) to open the high voltage contactor
relays.
Conditions for Clearing the DTC
DTCs P1B03 and P1B04 are Type A DTCs.
Diagnostic Aids
* The drive motor generator position sensor circuits operate at very low current. Extreme care must be taken when probing terminals and
manipulating harnesses.
* The sensor circuit loops are twisted pair with each pair covered in a foil shield. The shield circuits outside of the transmission are grounded to
a stud on the drive motor generator power inverter module (PIM) assembly.
* Ensure the drive motor generator position sensor harness shield circuits are properly grounded prior to testing.
Reference Information
Schematic Reference
Hybrid Controls Schematics ()
Connector End View Reference
* Component Connector End Views (See: Diagrams/Connector Views)
* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Special Tools
DT-48493 Jumper Harness
Circuit/System Testing
Note: The drive motor generator position sensor circuits require proper circuit integrity for correct system operation. Just a few ohms of
additional circuit resistance may cause position sensor signal degradation.
* Always inspect position sensor signal connectors for proper terminal contact.
* All diagnostic connections must be made with the approved test probes to prevent the creation of poor terminal contact.
* Connectors that contain position sensor signal circuits must always be clean and dry prior to mating. Foreign material or moisture within
the connector may cause sensor signal degradation.
1. Ignition OFF, disconnect PIM X1 connector.
2. Using the Position Sensor Specification table specifications listed below, test the position sensor resistance at the PIM X1 circuits as
indicated. Use the specifications for the drive motor generator that set the DTC. Also test each circuit for a short to ground.
锟斤拷If any of the circuits are not within specification, continue with testing.
锟斤拷If all circuits test normal, inspect for proper terminal contact at PIM X1 connector. If PIM X1 terminal contact tests OK, perform the
Intermittent Condition Testing below.
3. Disconnect the transmission X176 24-way connector.
4. Connect the DT-48493 to the X176 24-way connector at the transmission.
5. Using the Position Sensor Specification table specifications listed below, test the position sensor resistance at the transmission X176 circuits
as indicated. Use the specifications for the drive motor generator that set the DTC. Also test each circuit for a short to ground.
Diagnostic Repair parts ,Wiring Diagrams. DTC. TSB,Car, Truck, SUV & Van Acura Chrysler Infiniti Maserati Rolls-Royce Alfa Romeo Dodge Jaguar Mazda Scion Aston Martin Ferrari Jeep McLaren Smart Audi Fiat Karma Mercedes-Benz Spyker BMW Ford Kia Mini Subaru Bentley Freightliner Lamborghini Mitsubishi Tesla Bugatti GMC Land Rover Mobility Ventures Toyota Buick Genesis Lexus Nissan Volkswagen Cadillac Honda Lincoln Porsche Volvo Chevrolet Hyundai Lotus Ram
Thursday, October 31, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1681
Labels:
Cadillac Truck Escalade ESV AWD V8-6.2L Diagnostic Trouble Codes,
Conditions for Setting the DTC