Monday, January 6, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Technical Service Bulletin # 05-03-07-009C Date: 101209

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Technical Service Bulletin # 05-03-07-009C Date: 101209



Steering/Suspension - Wheel Alignment Specifications



WARRANTY ADMINISTRATION



Bulletin No.: 05-03-07-009C



Date: December 09, 2010



Subject: Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles



Models:



2011 and Prior GM Passenger Cars and Light Duty Trucks



2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 162



Supercede:



This bulletin is being extensively revised to provide technicians and warranty administrators with an all inclusive guide for wheel alignments.



PLEASE FAMILIARIZE YOURSELF WITH THESE UPDATES BEFORE PERFORMING YOUR NEXT GM WHEEL ALIGNMENT



SERVICE. Please discard Corporate Bulletin Number 05-03-07-009B (Section 03 - Suspension).



Purpose



The purpose of this bulletin is to provide retail, wholesale and fleet personnel with General Motors' warranty service requirements and



recommendations for customer concerns related to wheel alignment. For your convenience, this bulletin updates and centralizes all of GM's



Standard Wheel Alignment Service Procedures, Policy Guidelines and bulletins on wheel alignment warranty service.



Important



PLEASE FAMILIARIZE YOURSELF WITH THESE UPDATES BEFORE PERFORMING YOUR NEXT GM WHEEL ALIGNMENT



SERVICE.



The following five (5) key steps are a summary of this bulletin and are REQUIRED in completing a successful wheel alignment service.



1. Verify the vehicle is in an Original Equipment condition for curb weight, tires, wheels, suspension and steering configurations. Vehicles



modified in any of these areas are not covered for wheel alignment warranty.



2. Review the customer concern relative to "Normal Operation" definitions.



3. Verify that vehicle is within the "Mileage Policy" range.



4. Document wheel alignment warranty claims appropriately for labor operations E2000 and E2020.



The following information must be documented or attached to the repair order:



- Customer concern in detail



- What corrected the customer concern?



- If a wheel alignment is performed:



- Consult SI for proper specifications.



- Document the "Before" AND "After" wheel alignment measurements/settings.



- Completed "Wheel Alignment Repair Order Questionnaire" (form attached to this bulletin)



5. Use the proper wheel alignment equipment (preferred with print-out capability), process and the appropriate calibration maintenance



schedules.



Important



If it is determined that a wheel alignment is necessary under warranty, use the proper labor code for the repair. E2000 for Steering Wheel



Angle and/or Front Toe set or E2020 for Wheel Alignment Check/Adjust includes Caster, Camber and Toe set (Wheel alignment labor



time for other component repairs is to be charged to the component that causes a wheel alignment operation.).



The following flowchart is to help summarize the information detailed in this bulletin and should be used whenever a wheel alignment is



performed.



Verify Original Equipment Condition of the Vehicle



- Verify that Original Equipment Tires and Wheels or Official GM Accessory Tires and Wheels are on the vehicle.



- Verify that aftermarket suspension "Lift" or "Lowering" Kits or other suspension alterations have NOT been done to the vehicle.



- Check for accidental damage to the vehicle; for example, severe pothole or curb impacts, collision damage that may have affected the wheel



alignment of the vehicle; e.g., engine cradles, suspension control arms, axles, wheels, wheel covers, tires may show evidence of



damage/impact.



2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 163



- Check to be sure vehicle has seen "Normal Use" rather than abuse; e.g., very aggressive driving may show up by looking at the tires and



condition of the vehicle.



- Check for other additional equipment items that may significantly affect vehicle mass such as large tool boxes, campers, snow plow packages



(without the snowplow RPO), etc., especially in trucks and cutaway/incomplete vehicles. Significant additional mass can affect trim height



and wheel alignment of the vehicle and may necessitate a customer pay wheel alignment when placed semi-permanently in the vehicle



(Upfitter instructions are to realign the vehicle after placement of these types of items. (This typically applies to trucks and incomplete



vehicles that can be upfit with equipment such as the above.)



Customer Concerns, "Normal Operation" Conditions and "Mileage Policy"



Possible Concerns



The following are typical conditions that may require wheel alignment warranty service:



1. Lead/Pull: defined as "at a constant highway speed on a typical straight road, the amount of effort required at the steering wheel to maintain



the vehicle's straight heading."



Important



Please evaluate for the condition with hands-on the steering wheel. Follow the "Vehicle Leads/Pulls" diagnostic tree located in SI to



determine the cause of a lead/pull concern. Lead/Pull concerns can be due to road crown or road slope, tires, wheel alignment or even



in rare circumstances a steering gear issue. Lead/pull concerns due to road crown are considered "Normal Operation" and are NOT



a warrantable condition -- the customer should be advised that this is "Normal Operation."



Important



Some customers may comment on a "Lead/Pull" when they hold the steering wheel in a level condition. If so, this is more likely a



"steering wheel angle" concern because the customer is "steering" the vehicle to obtain a "level" steering wheel.



2. Steering wheel angle to the left or right (counter-clockwise or clockwise, respectively): Defined as the steering wheel angle (clocking)



deviation from "level" while maintaining a straight heading on a typical straight road.



3. Irregular or Premature tire wear: Slight to very slight "feathering" or "edge" wear on the shoulders of tires is NOT considered unusual



and should even out with a tire rotation; if the customer is concerned about a "feathering" condition of the tires, the customer could be



advised to rotate the tires earlier than the next scheduled mileage/maintenance interval (but no later than the next interval). Be sure to



understand the customer's driving habits as this will also heavily influence the tire wear performance; tire wear from aggressive or abusive



driving habits is NOT a warrantable condition.



Important



Slight or mild feathering, cupping, edge or heel/toe wear of tire tread shoulders is "normal" and can show up very early in a



tire/vehicle service mileage; in fact, some new tires can show evidence of feathering from the factory. These issues do NOT affect the



overall performance and tread life of the tire. Dealer personnel should always check the customer's maintenance records to ensure



that tire inflation pressure is being maintained to placard and that the tires are being rotated (modified-X pattern) at the proper



mileage intervals. Wheel alignments are NOT to be performed for the types of "Normal" Tire Feathering shown in Figures 1-4



below.



Figure 1: Full Tread View - "NORMAL" Tire "Feathering" Wear on the Shoulder/Adjacent/Center Ribs



Figure 2: Tire Shoulder View Example 1 - "NORMAL" Tire "Feathering" Wear on the Shoulder



Figure 3: Tire Shoulder View Example 2 - "NORMAL" Tire "Feathering" Wear



2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 164



Figure 4: Detail Side View of Tire Shoulder Area - "NORMAL" Tire "Feathering" Wear



Important



When a wheel alignment is deemed necessary for tire wear, be sure to document on the repair order, in as much detail as possible,



the severity and type of tire wear (e.g., severe center wear or severe inside or outside shoulder wear) and the position of the tire on



the vehicle (RF, LF, LR, RR). Please note the customer's concern with the wear such as, noise, appearance, wear life, etc. A field



product report with pictures of the tire wear condition is recommended. Refer to Corporate Bulletin Number 02-00-89-002J and



#07-00-89-036C.



4. Other repairs that affect wheel alignment; e.g., certain component replacement such as suspension control arm replacement, engine cradle



adjustment/replace, steering gear replacement, steering tie rod replace, suspension strut/shock, steering knuckle, etc. may require a wheel



alignment.



Important



If other components or repairs are identified as affecting the wheel alignment, policy calls for the wheel alignment labor time to be



charged to the replaced/repaired component's labor operation time rather than the wheel alignment labor operations.



Important



Vibration type customer concerns are generally NOT due to wheel alignment except in the rare cases; e.g., extreme diagonal wear



across the tread. In general, wheel alignments are NOT to be performed as an investigation/correction for vibration concerns.



"Normal Operation" Conditions



Vehicle Lead/Pull Due to Road Crown or Slope:



As part of "Normal Operation," vehicles will follow side-to-side or left to right road crown or slope. Be sure to verify from the customer the types



of roads they are driving as they may not recognize the influence of road crown on vehicle lead/pull and steering wheel angle. If a vehicle requires



significant steering effort to prevent it from "climbing" the road crown there may be an issue to be looked into further.



Important



A wheel alignment will generally NOT correct vehicles that follow the road crown since this is within "Normal Operation."



Mileage Policy



The following mileage policy applies for E2020 and E2000 labor operations:



Note



Wheel Alignment is NOT covered under the New Vehicle Limited Warranty for Express and Savana Cutaway vehicles as these vehicles require



Upfitters to set the wheel alignment after completing the vehicles.



- 0-800 km (0-500 mi): E2000/E2020 claims ONLY allowed with Call Center Authorization. Due to the tie down during shipping, the



vehicle's suspension requires some time to reach normal operating position. For this reason, new vehicles are generally NOT to be aligned



until they have accumulated at least 800 km (500 mi). A field product report should accompany any claim within this mileage range.



- 801-12,000 km (501-7,500 mi):



- If a vehicle came from the factory with incorrect alignment settings, any resulting off-angle steering wheel, lead/pull characteristics or the



rare occurrence of excessive tire wear would be apparent early in the life of the vehicle. The following policy applies:



- Vehicles 100% Factory Set/Measured for Caster/Camber/Toe - Escalade/ESV/EXT, Tahoe/Suburban, Yukon/XL/Denali,



Silverado/Sierra, Express/Savana, Corvette and Colorado/Canyon:



E2000/E2020 Claims: Call Center Authorization Required



- All Vehicles NOT 100% Factory Set/Measured for Caster/Camber/Toe as noted above:



E2000/E2020 Claims: Dealer Service Manager Authorization Required



- 12,001 km and beyond (7,501 miles and beyond): During this period, customers are responsible for the wheel alignment expense or



dealers may provide on a case-by case basis a one-time customer enthusiasm claim up to 16,000 km (10,000 mi). In the event that a defective



2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 165



component required the use of the subject labor operations, the identified defective component labor operation will include the appropriate



labor time for a wheel alignment as an add condition to the component repair.



Important



Only one wheel alignment labor operation claim (E2000 or E2020) may be used per VIN.



Warranty Documentation Requirements



When a wheel alignment service has been deemed necessary, the following items will need to be clearly documented on/with the repair order:



- Customer concern in detail



- What corrected the customer concern?



- If a wheel alignment is performed:



- Consult SI for proper specifications.



- Document the "Before" AND "After" wheel alignment measurements/settings.



- Completed "Wheel Alignment Repair Order Questionnaire" (form attached to this bulletin)



1. Document the customer concern in as much detail as possible on the repair order and in the warranty administration system. Preferred



examples:



- Steering wheel is off angle in the counterclockwise direction by approximately x degrees or clocking position.



- Vehicle lead/pulls to the right at approximately x-y mph. Vehicle will climb the road crown. Severe, Moderate or Slight.



- RF and LF tires are wearing on the outside shoulders with severe feathering.



Important



In the event of a lead/pull or steering wheel angle concern, please note the direction of lead/pull (left or right) or direction of



steering wheel angle (clockwise or counterclockwise) on the repair order and within the warranty claim verbatim.



Important



In the event of a tire wear concern, please note the position on the vehicle and where the wear is occurring on the tire; i.e., the RF



tire is wearing on the inside shoulder.



2. Document the technician's findings on cause and correction of the issue. Examples:



- Reset LF toe from 0.45 degrees to 0.10 degrees and RF toe from -0.25 degrees to 0.10 degrees to correct the steering wheel angle from 5



degrees counterclockwise to 0 degrees.



- Reset LF camber from 0.25 degrees to -0.05 degrees to correct the cross-camber condition of +0.30 degrees to 0.00 degrees on the



vehicle.



- Front Sum toe was found to be 0.50 degrees, reset to 0.20 degrees.



3. Print-out the "Before" and "After" wheel alignment measurements/settings and attach them to the Repair Order or if print-out capability is not



available, measurements may also be clearly and legibly handwritten into the Wheel Alignment Repair Order Questionnaire attached to this



bulletin.



4. Attach the Wheel Alignment Repair Order Questionnaire below along with the print-out of "Before" and "After" wheel alignment



measurements to the Repair Order and retain for use by GM.



Wheel Alignment Equipment and Process



Wheel alignments must be performed with a quality machine that will give accurate results when performing checks. "External Reference"



(image-based camera technology) is preferred. Please refer to Corporate Bulletin Number 05-00-89-029B: General Motors Dealership Critical



Equipment Requirements and Recommendations.



Requirements:



- Computerized four wheel alignment system.



- Computer capable of printing before and after alignment reports.



- Computer capable of time and date stamp printout.



- Racking system must have jacking capability



- Racking system must be capable of level to 1.6 mm (1/16 in)



- Appropriate wheel stops and safety certification



- Built-in turn plates and slip plates



- Wheel clamps capable of attaching to 20" or larger wheels



- Racking capable of accepting any GM passenger car or light duty truck



- Operator properly trained and ASE-certified (U.S. only) in wheel alignment



Recommendations:



Racking should have front and rear jacking capability.



2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 166



Equipment Maintenance and Calibration:



Alignment machines must be regularly calibrated in order to give correct information. Most manufacturers recommend the following:



- Alignment machines with "internal reference" sensors should be checked (and calibrated, if necessary) every six months.



- Alignment machines with "external reference" (image-based camera technology) should be checked (and calibrated, if necessary) once a



year.



- Racks must be kept level to within 1.6 mm (1/16 in).



- If any instrument that is part of the alignment machine is dropped or damaged in some way, check the calibration immediately.



Check with the manufacturer of your specific equipment for their recommended service/calibration schedule.



Wheel Alignment Process



When performing wheel alignment measurement and/or adjustment, the following steps should be taken:



Preliminary Steps:



1. Verify that the vehicle has a full tank of fuel (compensate as necessary).



2. Inspect the wheels and the tires for damage.



3. Inspect the tires for the proper inflation and irregular tire wear.



4. Inspect the wheel bearings for excessive play.



5. Inspect all suspension and steering parts for looseness, wear, or damage.



6. Inspect the steering wheel for excessive drag or poor return due to stiff or rusted linkage or suspension components.



7. Inspect the vehicle trim height.



8. Compensate for frame angle on targeted vehicles (refer to Wheel Alignment Specifications in SI).



Satisfactory vehicle operation may occur over a wide range of alignment angles. However, if the wheel alignment angles are not within the range of



specifications, adjust the wheel alignment to the specifications. Refer to Wheel Alignment Specifications in SI. Give consideration to excess loads,



such as tool boxes, sample cases, etc. Follow the wheel alignment equipment manufacturer's instructions.



Measure/Adjust:



Important



Prior to making any adjustments to wheel alignment on a vehicle, technicians must verify that the wheel alignment specifications loaded



into their wheel alignment machine are up-to-date by comparing these to the wheel alignment specifications for the appropriate model and



model year in SI. Using incorrect and/or outdated specifications may result in unnecessary adjustments, irregular and/or premature tire



wear and repeat customer concerns



Important



When performing adjustments to vehicles requiring a 4-wheel alignment, set the rear wheel alignment angles first in order to obtain



proper front wheel alignment angles.



Perform the following steps in order to measure the front and rear alignment angles:



1. Install the alignment equipment according to the manufacturer's instructions.



2. Jounce the front and the rear bumpers 3 times prior to checking the wheel alignment.



3. Measure the alignment angles and record the readings.



If necessary, adjust the wheel alignment to vehicle specification and record the before and after measurements. Refer to Wheel Alignment



Specifications in SI.



Important



Technicians must refer to SI for the correct wheel alignment specifications. SI is the only source of GM wheel alignment specifications that



is kept up-to-date throughout the year.



Test drive vehicle to ensure proper repair.



2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 167



Frame Angle Measurement (Express / Savana Only) ........



What corrected the customer concern and was the repair verified?



Please Explain: .............



2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 168