Tuesday, February 25, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1295

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1295



1. Ignition OFF, remove the fuse that supplies B+ to terminal 56-X2 of the ECM.



2. Disconnect the harness connector at the appropriate camshaft position sensor.



Note: The control module or the sensor may be damaged if the circuit is shorted to B+ voltage.



3. Test for 5 ohm or less between the low reference circuit terminal 1 and ground.



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the



circuit/connections test normal, replace the ECM.



4. Install the fuse that supplies B+ to terminal 56-X2 of the ECM.



5. Ignition ON, test for greater than 4.8 V between the 5-volt reference circuit terminal 3 and ground.



瀚慖f less than the specified value, test the 5-volt reference circuit for an open/high resistance. If the circuits/connections test normal, replace



the ECM.



6. Test for 4.8-5.2 V between the signal circuit terminal 2 and ground.



瀚慖f the voltage is greater than specified range, test for a short to voltage in the signal circuit. If circuit/connections test normal, replace the



ECM.



瀚慖f the voltage is less than the specified range, test for a short to ground or an open/high resistance in the signal circuit. If



circuit/connections test normal, replace the ECM.



7. If all circuits/connections test normal, replace the camshaft position sensor.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)



* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)



* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust)



* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and



programming



P0347



DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, or P0393 (LAU)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0341



- Intake Camshaft Position Sensor Performance Bank 1



DTC P0342



- Intake Camshaft Position Sensor Circuit Low Voltage Bank 1



DTC P0343



- Intake Camshaft Position Sensor Circuit High Voltage Bank 1



DTC P0346



- Intake Camshaft Position Sensor Performance Bank 2



DTC P0347



- Intake Camshaft Position Sensor Circuit Low Voltage Bank 2