2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1247
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- Transmission operation
- A damaged accessory drive component or belt; remove the belt and safely operate the engine to evaluate
* High resistance in the circuits of the injectors could set a misfire DTC without setting an injector DTC. Test the injector circuits of the
affected cylinder(s) for a high resistance if you suspect a condition.
Reference Information
Schematic Reference
Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
J 26792 HEI Spark Tester
Circuit/System Verification
1. Engine idling at the normal operating temperature, there should be no abnormal engine noise.
瀚慖f there is an abnormal engine noise, refer to Symptoms - Engine Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and
Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).
2. Verify that no other DTCs are set.
瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble
Code (DTC) List - Vehicle).
3. Observe the scan tool Misfire Current Cyl. 1-6 parameters. The Misfire Current Counters should not be incriminating.
4. Observe the scan tool Circuit Test Status parameters for the various components that may cause a misfire. Verify the Circuit Test Status
parameters for the components that may cause a misfire display OK or Not Run.
5. Engine idling, perform the cylinder power balance test with a scan tool to isolate the misfiring cylinder. The engine speed should change
when each injector is disabled.
6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Verify that the following conditions do not exist:
* Vacuum hose splits, kinks, and incorrect connections
* Engine vacuum leaks
* Crankcase ventilation system for vacuum leaks
* Fuel pressure that is too low or too high-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and
Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:
Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel
System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel
