2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1946
瀚慖f greater than the specified range, refer to Automatic Transmission Overheating (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Automatic
Transmission Overheating).
4. If neither the engine nor the transmission had an over temperature condition when the DTC set, replace the Q8 control solenoid valve
assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,
and programming.
Repair Verification
1. With a scan tool, clear the DTCs.
2. Operate the vehicle long enough to ensure the engine has reached normal operating temperature and the transmission fluid temperature has
stabilized between 80-98掳C (176-208掳F).
3. Observe the specific DTC P0218, and verify DTC P0218 has run and passed.
P219A
DTC P219A or P219B
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC P219A
- Fuel Trim Cylinder Balance Bank 1
DTC P219B
- Fuel Trim Cylinder Balance Bank 2
Circuit/System Description
The Fuel Trim Cylinder Balance diagnostic detects a rich or lean cylinder to cylinder air/fuel ratio imbalance in each bank. The diagnostic monitors
the pre-catalyst heated oxygen sensor (HO2S) signal's frequency and amplitude characteristics by calculating an accumulated voltage over a
predetermined sample period. An imbalance is indicated when multiple samples of the accumulated voltage are consistently higher than the desired
value.
Conditions for Running the DTC
* DTCs P0030, P0036, P0050, P0053, P0059, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0128, P0131, P0132, P0133,
P0134, P0135, P0151, P0152, P0153, P0154, P0155, P0201-P0206, P0300, P0301-P0306, P0411, P0412, P0418, P0442, P0443, P0446,
P0449, P0452, P0453, P0454, P0455, P0496, P1133, P1153, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176, P2431, P2432,
P2433, P2440, P2A00, P2A03 are not set.
* The device control is not active.
* The intrusive diagnostics are not active.
* The engine overspeed protection is not active.
* The power take-off (PTO) is not active.
* The traction control is not active.
* The fuel control is in air-fuel Closed Loop.
* The system voltage is more than 10 V, or less than 18 V.
* The engine run time is greater than 100 s.
* The engine coolant temperature (ECT) is greater than -20掳C (-4掳F).
* The engine speed is greater than 425 RPM, but less than 6,000 RPM.
* The mass air flow is greater than 25 g/s, but less than 510 g/s.
Conditions for Setting the DTC
