Showing posts with label 瀚慖f greater than the specified range. Show all posts
Showing posts with label 瀚慖f greater than the specified range. Show all posts

Tuesday, December 1, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2501

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2501

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal E and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

4. Test for less than 1 V between the TP sensor 1 signal circuit terminal D and ground.

瀚慖f greater than specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

5. Install a 3 A fused jumper wire between TP sensor 1 signal circuit terminal D and the 5 V reference circuit terminal E. Verify the scan tool

TP sensor 1 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the ECM.

6. Test for 4.8-5.2 V between the TP sensor 2 signal circuit terminal F and ground.

瀚慖f less than specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

ECM.

瀚慖f greater than specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

7. If all circuits test normal, test or replace the throttle body assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Throttle Body Assembly Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Throttle Body/Service and

Repair/Removal and Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement,

programming, and setup

P2138

DTC P2120, P2122, P2123, P2125, P2127, P2128, or P2138

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provide an overview of each diagnostic category.

DTC Descriptors

DTC P2120

- Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122

- Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123

- Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125

- Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127

- Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128

- Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2494

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2494

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit/connections test normal, replace

the ECM.

3. Ignition ON, test for 4.8-5.2 V between the appropriate 5 V reference circuit terminal listed below and ground.

* APP sensor 1 terminal D or 2

* APP sensor 2 terminal C or 1

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or open/high resistance. If the circuit/connections test

normal, replace the ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit/connections test normal, replace the

ECM.

4. Observe the scan tool APP sensor 1 voltage parameter. Verify the voltage is less than 0.3 V.

瀚慖f greater than the specified range, test the signal circuit terminal E or 3 for a short to voltage. If the circuit/connections test normal,

replace the ECM.

5. Observe the scan tool APP sensor 2 voltage parameter. Verify the voltage is less than 0.3 V.

瀚慖f greater than the specified range, test the signal circuit terminal B or 6 for a short to voltage. If the circuit/connections test normal,

replace the ECM.

6. Connect a 3 A fused jumper wire between the APP sensor 1 signal circuit terminal E or 3 and the 5 V reference circuit terminal C or 1. Verify

the APP sensor 1 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit/connections test

normal, replace the ECM.

7. Connect a 3 A fused jumper wire between the APP sensor 2 signal circuit terminal B or 6 and the 5 V reference circuit terminal C or 1.

Verify the APP sensor 2 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit/connections test

normal, replace the ECM.

8. If all circuits/connections test normal, test or replace the Accelerator Pedal Assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Accelerator Pedal Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Accelerator Pedal Position

Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement,

programming, and setup

P2128

DTC P2120, P2122, P2123, P2125, P2127, P2128, or P2138

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provide an overview of each diagnostic category.

DTC Descriptors

DTC P2120

- Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122

- Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123

- Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

Monday, November 30, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2487

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2487

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit/connections test normal, replace

the ECM.

3. Ignition ON, test for 4.8-5.2 V between the appropriate 5 V reference circuit terminal listed below and ground.

* APP sensor 1 terminal D or 2

* APP sensor 2 terminal C or 1

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or open/high resistance. If the circuit/connections test

normal, replace the ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit/connections test normal, replace the

ECM.

4. Observe the scan tool APP sensor 1 voltage parameter. Verify the voltage is less than 0.3 V.

瀚慖f greater than the specified range, test the signal circuit terminal E or 3 for a short to voltage. If the circuit/connections test normal,

replace the ECM.

5. Observe the scan tool APP sensor 2 voltage parameter. Verify the voltage is less than 0.3 V.

瀚慖f greater than the specified range, test the signal circuit terminal B or 6 for a short to voltage. If the circuit/connections test normal,

replace the ECM.

6. Connect a 3 A fused jumper wire between the APP sensor 1 signal circuit terminal E or 3 and the 5 V reference circuit terminal C or 1. Verify

the APP sensor 1 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit/connections test

normal, replace the ECM.

7. Connect a 3 A fused jumper wire between the APP sensor 2 signal circuit terminal B or 6 and the 5 V reference circuit terminal C or 1.

Verify the APP sensor 2 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit/connections test

normal, replace the ECM.

8. If all circuits/connections test normal, test or replace the Accelerator Pedal Assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Accelerator Pedal Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Accelerator Pedal Position

Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement,

programming, and setup

P2125

DTC P2120, P2122, P2123, P2125, P2127, P2128, or P2138

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provide an overview of each diagnostic category.

DTC Descriptors

DTC P2120

- Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122

- Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123

- Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2480

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2480

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit/connections test normal, replace

the ECM.

3. Ignition ON, test for 4.8-5.2 V between the appropriate 5 V reference circuit terminal listed below and ground.

* APP sensor 1 terminal D or 2

* APP sensor 2 terminal C or 1

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or open/high resistance. If the circuit/connections test

normal, replace the ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit/connections test normal, replace the

ECM.

4. Observe the scan tool APP sensor 1 voltage parameter. Verify the voltage is less than 0.3 V.

瀚慖f greater than the specified range, test the signal circuit terminal E or 3 for a short to voltage. If the circuit/connections test normal,

replace the ECM.

5. Observe the scan tool APP sensor 2 voltage parameter. Verify the voltage is less than 0.3 V.

瀚慖f greater than the specified range, test the signal circuit terminal B or 6 for a short to voltage. If the circuit/connections test normal,

replace the ECM.

6. Connect a 3 A fused jumper wire between the APP sensor 1 signal circuit terminal E or 3 and the 5 V reference circuit terminal C or 1. Verify

the APP sensor 1 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit/connections test

normal, replace the ECM.

7. Connect a 3 A fused jumper wire between the APP sensor 2 signal circuit terminal B or 6 and the 5 V reference circuit terminal C or 1.

Verify the APP sensor 2 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit/connections test

normal, replace the ECM.

8. If all circuits/connections test normal, test or replace the Accelerator Pedal Assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Accelerator Pedal Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Accelerator Pedal Position

Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement,

programming, and setup

P2122

DTC P2120, P2122, P2123, P2125, P2127, P2128, or P2138

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provide an overview of each diagnostic category.

DTC Descriptors

DTC P2120

- Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122

- Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123

- Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

Friday, November 13, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2074

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2074

瀚慖f greater than the specified range, test the signal circuit terminal 1 for a short to voltage. If the circuit tests normal, replace the ECM.

5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and the 5-volt reference circuit terminal 3. Verify the scan tool FTP

sensor parameter is greater than 4.7 volts.

瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the

ECM.

6. If all circuits test normal, test or replace the FTP sensor.

Repair Instructions

* For DTC P0452 or P0453, always perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic

procedure

* For DTC P0451 or P0454, clear DTCs with a scan tool

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup and programming

P0452

DTC P0451-P0454

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0451

- Fuel Tank Pressure (FTP) Sensor Performance

DTC P0452

- Fuel Tank Pressure (FTP) Sensor Circuit Low Voltage

DTC P0453

- Fuel Tank Pressure (FTP) Sensor Circuit High Voltage

DTC P0454

- Fuel Tank Pressure (FTP) Sensor Intermittent

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

The fuel tank pressure (FTP) sensor measures air pressure or vacuum in the evaporative emission (EVAP) system. The engine control module

(ECM) supplies a 5-volt reference and a low reference circuit to the FTP sensor. The FTP sensor signal voltage varies depending on EVAP system

Wednesday, November 11, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2018

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2018

瀚慖f greater than the specified range, test the circuits for a short to voltage. If the circuits test normal, replace the ECM.

9. Test for intermittent or poor connections at the ECM, KS, and in-line connectors where present.

10. If all circuits test normal, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Knock Sensor 1 Replacement (See: Powertrain Management/Computers and Control Systems/Knock Sensor/Service and Repair/Knock

Sensor 1 Replacement)

* Knock Sensor 2 Replacement (See: Powertrain Management/Computers and Control Systems/Knock Sensor/Service and Repair/Knock

Sensor 2 Replacement)

* Engine Control Module Replacement (See: Powertrain Management/Computers and Control Systems/Engine Control Module/Service and

Repair)

* Engine Control Module Programming and Setup (See: Powertrain Management/Computers and Control Systems/Engine Control

Module/Testing and Inspection)

P0330

DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0324

- Knock Sensor (KS) Module Performance

DTC P0325

- Knock Sensor (KS) Circuit Bank 1

DTC P0326

- Knock Sensor (KS) Performance

DTC P0327

- Knock Sensor (KS) Circuit Low Voltage Bank 1

DTC P0328

- Knock Sensor (KS) Circuit High Voltage Bank 1

DTC P0330

- Knock Sensor (KS) Circuit Bank 2

DTC P0332

- Knock Sensor (KS) Circuit Low Voltage Bank 2

DTC P0333

- Knock Sensor (KS) Circuit High Voltage Bank 2

Diagnostic Fault Information

Circuit/System Description

The knock sensor (KS) system enables the engine control module (ECM) to control the ignition timing for the best possible performance while

protecting the engine from potentially damaging levels of detonation. The ECM monitors 2 separate KS, one on each side of the engine block. Each

KS produces an AC voltage that varies, depending on the vibration levels detected during engine operation. The ECM receives the KS signal

Monday, November 9, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1969

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1969

瀚慖f greater than the specified range, replace the hood ajar switch.

4. With the switch in the hood open position, test for infinite resistance between the ground terminal C and the signal terminal B.

瀚慖f not infinite, replace the hood ajar switch.

5. Test for less than 2.0 ohms between the ground terminal C and the signal terminal A.

瀚慖f greater than the specified range, replace the hood ajar switch.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Hood Primary and Secondary Latch Replacement (See: Body and Frame/Doors, Hood and Trunk/Hood/Hood Latch/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup

P279D

DTC P279D

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptor

DTC P279D

- Four Wheel Drive (4WD) Range Signal Circuit

Circuit/System Description

The hybrid powertrain control module (HPCM) monitors the state of the 4WD range signal message, if equipped, over the GMLAN communication

bus. The HPCM uses this message to determine motor torque required and transmission shifting, there are no external circuits involved.

Conditions for Running the DTC

The engine is running.

Conditions for Setting the DTC

The HPCM has detected a 4WD range signal rolling count error for 8 seconds.

Action Taken When the DTC Sets

DTC P279D is a Type A DTC.

Conditions for Clearing the DTC

* DTC P279D is a Type A DTC.

* When attempting to set HPCM internal DTCs, run the engine for at least 1 minute, and then shut the engine off for 30 seconds. Following

this procedure will allow for a complete HPCM shutdown. Program the HPCM with the latest software version and retest the DTC to see if

the DTC resets.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

Sunday, November 8, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1946

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1946

瀚慖f greater than the specified range, refer to Automatic Transmission Overheating (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Automatic

Transmission Overheating).

4. If neither the engine nor the transmission had an over temperature condition when the DTC set, replace the Q8 control solenoid valve

assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,

and programming.

Repair Verification

1. With a scan tool, clear the DTCs.

2. Operate the vehicle long enough to ensure the engine has reached normal operating temperature and the transmission fluid temperature has

stabilized between 80-98掳C (176-208掳F).

3. Observe the specific DTC P0218, and verify DTC P0218 has run and passed.

P219A

DTC P219A or P219B

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptors

DTC P219A

- Fuel Trim Cylinder Balance Bank 1

DTC P219B

- Fuel Trim Cylinder Balance Bank 2

Circuit/System Description

The Fuel Trim Cylinder Balance diagnostic detects a rich or lean cylinder to cylinder air/fuel ratio imbalance in each bank. The diagnostic monitors

the pre-catalyst heated oxygen sensor (HO2S) signal's frequency and amplitude characteristics by calculating an accumulated voltage over a

predetermined sample period. An imbalance is indicated when multiple samples of the accumulated voltage are consistently higher than the desired

value.

Conditions for Running the DTC

* DTCs P0030, P0036, P0050, P0053, P0059, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0128, P0131, P0132, P0133,

P0134, P0135, P0151, P0152, P0153, P0154, P0155, P0201-P0206, P0300, P0301-P0306, P0411, P0412, P0418, P0442, P0443, P0446,

P0449, P0452, P0453, P0454, P0455, P0496, P1133, P1153, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176, P2431, P2432,

P2433, P2440, P2A00, P2A03 are not set.

* The device control is not active.

* The intrusive diagnostics are not active.

* The engine overspeed protection is not active.

* The power take-off (PTO) is not active.

* The traction control is not active.

* The fuel control is in air-fuel Closed Loop.

* The system voltage is more than 10 V, or less than 18 V.

* The engine run time is greater than 100 s.

* The engine coolant temperature (ECT) is greater than -20掳C (-4掳F).

* The engine speed is greater than 425 RPM, but less than 6,000 RPM.

* The mass air flow is greater than 25 g/s, but less than 510 g/s.

Conditions for Setting the DTC

Monday, November 2, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1818

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1818

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

5. If all circuits test normal, replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming

P0153

DTC P0133, P013A-P013F, P014A, P014B, P0153, P1133, or P1153

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0133

- HO2S Slow Response Bank 1 Sensor 1

DTC P013A

- HO2S Slow Response Rich to Lean Bank 1 Sensor 2

DTC P013B

- HO2S Slow Response Lean to Rich Bank 1 Sensor 2

DTC P013C

- HO2S Slow Response Rich to Lean Bank 2 Sensor 2

DTC P013D

- HO2S Slow Response Lean to Rich Bank 2 Sensor 2

DTC P013E

- HO2S Delayed Response Rich to Lean Bank 1 Sensor 2

DTC P013F

- HO2S Delayed Response Lean to Rich Bank 1 Sensor 2

DTC P014A

- HO2S Delayed Response Rich to Lean Bank 2 Sensor 2

DTC P014B

- HO2S Delayed Response Lean to Rich Bank 2 Sensor 2

DTC P0153

- HO2S Slow Response Bank 2 Sensor 1

Sunday, November 1, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1778

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1778

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal E and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

4. Test for less than 1 V between the TP sensor 1 signal circuit terminal D and ground.

瀚慖f greater than specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

5. Install a 3 A fused jumper wire between TP sensor 1 signal circuit terminal D and the 5 V reference circuit terminal E. Verify the scan tool

TP sensor 1 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the ECM.

6. Test for 4.8-5.2 V between the TP sensor 2 signal circuit terminal F and ground.

瀚慖f less than specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

ECM.

瀚慖f greater than specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

7. If all circuits test normal, test or replace the throttle body assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Throttle Body Assembly Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Throttle Body/Service and

Repair/Removal and Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement,

programming, and setup

P0123

DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0120

- Throttle Position (TP) Sensor 1 Circuit

DTC P0122

- Throttle Position (TP) Sensor 1 Circuit Low Voltage

DTC P0123

- Throttle Position (TP) Sensor 1 Circuit High Voltage

DTC P0220

- Throttle Position (TP) Sensor 2 Circuit

DTC P0222

- Throttle Position (TP) Sensor 2 Circuit Low Voltage

DTC P0223

- Throttle Position (TP) Sensor 2 Circuit High Voltage

Friday, February 7, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1669

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1669



瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.



4. Ignition ON, verify the scan tool ECM PNP Switch parameter displays In Gear.



瀚慖f not the specified value, test the P/N signal circuit for a short to ground. If the circuit tests normal, replace the engine control module.



5. Connect a 3-amp fused jumper wire between the TCM harness connector terminal 3 and terminal 18. Verify the PNP Switch parameter



changes to Park/Neutral.



瀚慖f not the specified value, test the P/N signal circuit for an open/high resistance. If the circuit tests normal, replace the engine control



module.



6. Ignition OFF, remove the control valve body cover. Refer to Control Valve Body Cover Replacement (See: Transmission and



Drivetrain/Automatic Transmission/Transaxle/Valve Body/Service and Repair/6T70/6T75 - Automatic Transmission/Control Valve Body



Cover Replacement).



7. Connect the TCM harness connector.



8. Disconnect the IMS connector at the control solenoid valve assembly.



9. Ignition ON, verify the scan tool IMS A/B/C/P parameter displays HI for all four signal circuits.



瀚慖f not the specified value, replace the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control



Module Assembly Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission



and Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).



10. Verify the scan tool ECM PNP Switch parameter displays In Gear.



瀚慖f not the specified value, replace the control solenoid valve assembly.



11. Connect a 3-amp fused jumper wire between each transmission range signal circuit terminal listed below and the IMS ground circuit,



terminal A. Verify the corresponding scan tool IMS A/B/C/P parameter displays LOW when terminals E, D, C, and B are connected to the



IMS ground and the ECM PNP Switch parameter displays Park/Neutral when terminal F is connected to ground.



* Switch Signal A terminal E



* Switch Signal B terminal D



* Switch Signal C terminal C



* Switch Signal P terminal B



* PNP Switch Signal terminal F



瀚慖f not the specified value, replace the control solenoid valve assembly.



12. If all circuits test normal, replace the IMS.



Repair Instructions



Important:



* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and



Inspection/Programming and Relearning) following all transmission related repairs.



* Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See:



Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General



Diagnostics/6T70/6T75 - Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM or control solenoid valve assembly



replacement, setup, and programming



* Range Selector Lever Cable Adjustment (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Shift Linkage/Shift



Cable/Adjustments)



* Control Valve Body Cover Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Valve Body/Service and



Repair/6T70/6T75 - Automatic Transmission/Control Valve Body Cover Replacement)



* Manual Shift Detent Lever with Shaft Position Switch Assembly Replacement (See: Powertrain Management/Computers and Control



Systems/Sensors and Switches - Computers and Control Systems/Transmission Position Sensor/Switch/Service and Repair)



P0851



DTC P0850-P0852



Diagnostic Instructions

Monday, January 20, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1176

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1176



瀚慖f greater than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal,



replace the K20 ECM.



7. If the circuits test normal, test or replace the B65 intake air pressure and temperature sensor.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Turbocharger Pressure Sensor Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Turbocharger/Service and



Repair/Turbocharger Pressure Sensor Replacement) for intake air pressure and temperature sensor replacement



* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and



programming



P0237



DTC P0236, P0237, or P0238



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0236



- Turbocharger Boost System Performance



DTC P0237



- Turbocharger Boost Sensor Circuit Low Voltage



DTC P0238



- Turbocharger Boost Sensor Circuit High Voltage



Diagnostic Fault Information



Typical Scan Tool Data



Circuit Description



The boost pressure sensor is integrated with the intake air temperature (IAT) sensor. The boost pressure sensor measures the range of pressures



between the turbocharger and the throttle body. Pressure in this portion of the induction system is affected by the following:

Thursday, January 16, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1048

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1048



瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.



4. Install fuse that supplies B+ to terminal 56 X2 of the ECM.



Caution: Do NOT use the low reference circuit in the component harness connector for this test. Damage to the control module may occur



due to excessive current draw.



5. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 4 and ground.



瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and



the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.



6. Test for 4.8-5.2 V between the signal circuit terminal 5 and the ground circuit terminal 2.



瀚慖f less than the specified range, test the signal circuit for an open/high resistance or a short to ground. If the circuit/connections test



normal, replace the K20 ECM.



瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit/connections test normal, replace the K20



ECM.



7. Ignition OFF, connect the red lead of the J 38522 to the signal circuit terminal 5 at the B75 MAF sensor harness connector. Connect the



battery voltage supply to B+, and the black lead to ground.



8. Set the J 38522 Signal switch to 5 V, the Frequency switch to 5K, and the Duty Cycle switch to Normal.



9. Ignition ON, observe the scan tool MAF Sensor Hz parameter. The parameter should be between 4,950-5,050 Hz.



瀚慖f the parameter is not within the specified range, replace the K20 ECM.



10. If all circuits/connections test normal, replace the B75 MAF sensor.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Mass Airflow Sensor with Intake Air Temperature Sensor Replacement (LF1) (See: Powertrain Management/Computers and Control



Systems/Air Temperature Sensor ( Ambient / Intake )/Service and Repair)Mass Airflow Sensor with Intake Air Temperature Sensor



Replacement (LAU) (See: Powertrain Management/Computers and Control Systems/Air Temperature Sensor ( Ambient / Intake )/Service



and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and



programming



P0106



DTC P0106 (LF1)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptor



DTC P0106



- Manifold Absolute Pressure (MAP) Sensor Performance



Diagnostic Fault Information



Typical Scan Tool Data

Monday, January 13, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1333

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1333



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the



circuit/connections test normal, replace the ECM.



4. Install the fuse that supplies B+ to terminal 56-X2 of the ECM.



5. Ignition ON, test for greater than 4.8 V between the 5-volt reference circuit terminal 3 and ground.



瀚慖f less than the specified value, test the 5-volt reference circuit for an open/high resistance. If the circuits/connections test normal, replace



the ECM.



6. Test for 4.8-5.2 V between the signal circuit terminal 2 and ground.



瀚慖f the voltage is greater than specified range, test for a short to voltage in the signal circuit. If circuit/connections test normal, replace the



ECM.



瀚慖f the voltage is less than the specified range, test for a short to ground or an open/high resistance in the signal circuit. If



circuit/connections test normal, replace the ECM.



7. If all circuits/connections test normal, replace the camshaft position sensor.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)



* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)



* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust)



* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and



programming



P0392



DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, or P0393 (LAU)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0341



- Intake Camshaft Position Sensor Performance Bank 1



DTC P0342



- Intake Camshaft Position Sensor Circuit Low Voltage Bank 1



DTC P0343



- Intake Camshaft Position Sensor Circuit High Voltage Bank 1



DTC P0346



- Intake Camshaft Position Sensor Performance Bank 2



DTC P0347



- Intake Camshaft Position Sensor Circuit Low Voltage Bank 2



DTC P0348



- Intake Camshaft Position Sensor Circuit High Voltage Bank 2



DTC P0366



- Exhaust Camshaft Position Sensor Performance Bank 1

Wednesday, December 18, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 97

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 97

瀚慖f greater than the specified range, test the circuit for a short to voltage.

13. Ignition OFF, test for infinite resistance between the high circuit terminals listed below and ground.

* Driver steering wheel air bag coil connector Stage 1 terminal A X1

* Driver steering wheel air bag coil connector Stage 2 terminal A X2

瀚慖f less than the specified value, test the circuit for a short to ground.

14. Test for infinite resistance between the low circuit terminals listed below and ground.

* Driver steering wheel air bag coil connector Stage 1 terminal B X1

* Driver steering wheel air bag coil connector Stage 2 terminal B X2

瀚慖f less than the specified value, test the circuit for a short to ground.

15. Test for less then 1 ohm between the SDM connector and the air bag connector high circuit terminals listed below.

* Driver steering wheel air bag coil connector Stage 1 terminal A X1 and SDM terminal 4 X1.

* Driver steering wheel air bag coil connector Stage 2 terminal A X2 and SDM terminal 1 X1.

瀚慖f greater than the specified range, test the circuit for an open/high resistance.

16. Test for less then 1 ohm between the SDM connector and the air bag connector low circuit terminals listed below.

* Driver steering wheel air bag coil connector Stage 1 terminal B X1 and SDM terminal 3 X1

* Driver steering wheel air bag coil connector Stage 2 terminal B X2 and SDM terminal 2 X1

瀚慖f greater than the specified range, test the circuit for an open/high resistance.

17. If all circuits test normal, replace the SDM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Steering Wheel Inflatable Restraint Module Coil Replacement (See: Restraints and Safety Systems/Air Bag Systems/Clockspring Assembly

/ Spiral Cable/Service and Repair/Removal and Replacement)

* Steering Wheel Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and

Repair/Removal and Replacement/Steering Wheel Inflatable Restraint Module Replacement)

* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/SIR/SRS Wiring Repairs)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for SDM replacement, setup, and programming

B0014

DTC B0014-B0045

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B0014 01

- Driver Side Seat Air Bag Deployment Loop Short to Battery

DTC B0014 02

- Driver Side Seat Air Bag Deployment Loop Short to Ground

DTC B0014 04

- Driver Side Seat Air Bag Deployment Loop Open Circuit

Monday, December 9, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 769

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 769

瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.

3. Ignition ON, verify that a test lamp illuminates between the B+ circuits listed below and ground.

* Terminal 1

* Terminal 25

瀚慖f the test lamp does not illuminate, test the appropriate circuit for a short to ground or an open/high resistance.

4. If all circuits test normal, replace the EBCM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming

Brake Boost Solenoid

DTC C012F, C12A7, C12DC, or C12DD

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC C012F 00

- Brake Boost Solenoid Valve Circuit

DTC C012F 0E

- Brake Boost Solenoid Valve Circuit Shorted

DTC C12A7

- Brake Boost Solenoid Valve Circuit Performance

DTC C12DC

- Brake Boost Solenoid Valve Circuit Malfunction

DTC C12DD

- Brake Boost Solenoid Valve Circuit Shorted

Circuit/System Description

The electronic brake control module (EBCM) uses input from the boost pressure sensor for more accurate control during brake and vehicle stability

enhancement system (VSES) event. The boost pressure sensor is internal to the brake pressure modulator valve (BPMV).

Conditions for Running the DTC

* The ignition is ON.

* Ignition voltage is greater than 10 volts.

Conditions for Setting the DTC

C012F 00, C12A7, C12DC

Solonoid feedback current greater than 25% of commanded current.

C012F 0E, C12DD

Solonoid feedback current greater than 50% of requested current.

Action Taken When the DTC Sets

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 760

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 760

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the HVAC

control module.

3. Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal 1 and low reference circuit terminal 2.

瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the

HVAC control module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HVAC control

module.

4. If all circuits test normal, test or replace the evaporator air temperature sensor.

Component Testing

1. Test the evaporator air temperature sensor by varying the sensor temperature while monitoring the sensor resistance.

2. Compare the readings with the Sensor Resistance Table (See: Heating and Air Conditioning/Specifications/Electrical Specifications) and

verify that the resistance is within 5 percent of the specification.

瀚慖f not within the specified range, replace the sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Air Conditioning Refrigerant Temperature Sensor Replacement (See: Heating and Air Conditioning/Refrigerant Temperature

Sensor/Service and Repair/HVAC - Automatic)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for HVAC control module replacement, setup, and

programming

B3935

DTC B3935

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC B3935 57

- Transponder Authentication Error

Circuit/System Description

When an ignition key is inserted into the ignition lock cylinder and the ignition is switched ON, the transponder embedded in the head of the key is

energized by the exciter coils surrounding the ignition lock cylinder. The energized transponder transmits a signal that contains its unique value,

which is received by the theft deterrent module (TDM). The TDM then compares this value to a value stored in memory. This stored value is the

learned key code. If the value is correct, the TDM will send the prerelease password via the serial data circuit to the engine control module (ECM).

If the transponder value does not match the learned key code or a transponder value is not received, the TDM will send the start disable password to

the ECM.

Conditions for Running the DTC

* Ignition is in the Accessory or Run position.

* A valid transponder value has been read.

Conditions for Setting the DTC

* The transponder value is valid and matches the value stored in the TDM memory.

* The transponder calculation to the challenge from the TDM does not match the TDM calculation.

Action Taken When the DTC Sets

Thursday, November 28, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 533

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 533

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

6. If all circuits test normal, replace the HSM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)

()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming

B2180

DTC B1935 or B2180 (Dealer Installed)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B1935 04

- Left Seat Back Heater Circuit Open

DTC B1935 0A

- Left Seat Back Heater Circuit Rate of Change Below Threshold

DTC B1935 0B

- Left Seat Back Heater Circuit Current Above Threshold

DTC B1935 0C

- Left Seat Back Heater Circuit Current Below Threshold

DTC B1935 0D

- Left Seat Back Heater Circuit Resistance Above Threshold

DTC B1935 0E

- Left Seat Back Heater Circuit Resistance Below Threshold

DTC B1935 1F

- Left Seat Back Heater Circuit Intermittent

DTC B2180 04

- Right Seat Back Heater Circuit Open

DTC B2180 0A

- Right Seat Back Heater Circuit Rate of Change Below Threshold

DTC B2180 0B

- Right Seat Back Heater Circuit Current Above Threshold

DTC B2180 0C

- Right Seat Back Heater Circuit Current Below Threshold

DTC B2180 0D

- Right Seat Back Heater Circuit Resistance Above Threshold

DTC B2180 0E

- Right Seat Back Heater Circuit Resistance Below Threshold

DTC B2180 1F

- Right Seat Back Heater Circuit Intermittent

Diagnostic Fault Information

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 523

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 523

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

6. If all circuits test normal, replace the HSM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)

()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming

HP2 W/O Memory

DTC B1935 or B2180 (HP2 w/o Memory)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B1935 04

- Left Seat Back Heater Circuit Open

DTC B1935 0A

- Left Seat Back Heater Circuit Rate of Change Below Threshold

DTC B1935 0B

- Left Seat Back Heater Circuit Current Above Threshold

DTC B1935 0C

- Left Seat Back Heater Circuit Current Below Threshold

DTC B1935 0D

- Left Seat Back Heater Circuit Resistance Above Threshold

DTC B1935 0E

- Left Seat Back Heater Circuit Resistance Below Threshold

DTC B1935 1F

- Left Seat Back Heater Circuit Intermittent

DTC B2180 04

- Right Seat Back Heater Circuit Open

DTC B2180 0A

- Right Seat Back Heater Circuit Rate of Change Below Threshold

DTC B2180 0B

- Right Seat Back Heater Circuit Current Above Threshold

DTC B2180 0C

- Right Seat Back Heater Circuit Current Below Threshold

DTC B2180 0D

- Right Seat Back Heater Circuit Resistance Above Threshold

DTC B2180 0E

- Right Seat Back Heater Circuit Resistance Below Threshold

DTC B2180 1F

- Right Seat Back Heater Circuit Intermittent

Diagnostic Fault Information

Wednesday, November 27, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 515

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 515

瀚慖f greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the MSM.

5. Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 3. Verify the scan tool Driver

Seat Recline Sensor parameter is greater than 4.75 volts.

瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the

MSM.

6. If all circuits test normal, test or replace the seat recline position sensor.

B2355 01, B2355 06, B2365 01, B2365 06, B2375 01 or B2375 06

1. Ignition OFF, disconnect the X2 harness connector at the seat adjuster assembly.

2. Test for less than 2 ohms between the low reference circuit terminal 2 and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 6 and ground.

瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the MSM.

瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.

4. Verify the appropriate scan tool driver seat sensor parameter is less than 1 volt.

瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace

the MSM.

* Seat front vertical position sensor terminal 1

* Seat rear vertical position sensor terminal 5

* Seat horizontal position sensor terminal 3

5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal 6. Verify the

appropriate scan tool driver seat position sensor parameter is greater than 4.75 volts.

* Seat horizontal position sensor terminal 3

* Seat front vertical position sensor terminal 1

* Seat rear vertical position sensor terminal 5

瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the

MSM.

6. If all circuits test normal, test or replace the seat position sensor.

B1850 01, B1850 06, B1860 01 or B1860 06

1. Ignition OFF, disconnect the X2 harness connector at the lumbar adjuster assembly.

2. Test for less than 2 ohms between the low reference circuit terminal C and ground.

瀚慖f greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.

瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the MSM.

瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.

4. Verify the appropriate scan tool lumbar sensor parameter is less than 1 volt.

瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace

the MSM.

* Lumbar vertical position sensor terminal B

* Lumbar horizontal position sensor terminal D

5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal A. Verify the

appropriate scan tool lumbar sensor parameter is greater than 4.75 volts.

* Lumbar vertical position sensor terminal B

* Lumbar horizontal position sensor terminal D