Showing posts with label test the signal circuit for a short to voltage. If the circuit tests normal. Show all posts
Showing posts with label test the signal circuit for a short to voltage. If the circuit tests normal. Show all posts

Thursday, November 28, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 533

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 533

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

6. If all circuits test normal, replace the HSM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)

()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming

B2180

DTC B1935 or B2180 (Dealer Installed)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B1935 04

- Left Seat Back Heater Circuit Open

DTC B1935 0A

- Left Seat Back Heater Circuit Rate of Change Below Threshold

DTC B1935 0B

- Left Seat Back Heater Circuit Current Above Threshold

DTC B1935 0C

- Left Seat Back Heater Circuit Current Below Threshold

DTC B1935 0D

- Left Seat Back Heater Circuit Resistance Above Threshold

DTC B1935 0E

- Left Seat Back Heater Circuit Resistance Below Threshold

DTC B1935 1F

- Left Seat Back Heater Circuit Intermittent

DTC B2180 04

- Right Seat Back Heater Circuit Open

DTC B2180 0A

- Right Seat Back Heater Circuit Rate of Change Below Threshold

DTC B2180 0B

- Right Seat Back Heater Circuit Current Above Threshold

DTC B2180 0C

- Right Seat Back Heater Circuit Current Below Threshold

DTC B2180 0D

- Right Seat Back Heater Circuit Resistance Above Threshold

DTC B2180 0E

- Right Seat Back Heater Circuit Resistance Below Threshold

DTC B2180 1F

- Right Seat Back Heater Circuit Intermittent

Diagnostic Fault Information

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 523

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 523

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

6. If all circuits test normal, replace the HSM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)

()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming

HP2 W/O Memory

DTC B1935 or B2180 (HP2 w/o Memory)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B1935 04

- Left Seat Back Heater Circuit Open

DTC B1935 0A

- Left Seat Back Heater Circuit Rate of Change Below Threshold

DTC B1935 0B

- Left Seat Back Heater Circuit Current Above Threshold

DTC B1935 0C

- Left Seat Back Heater Circuit Current Below Threshold

DTC B1935 0D

- Left Seat Back Heater Circuit Resistance Above Threshold

DTC B1935 0E

- Left Seat Back Heater Circuit Resistance Below Threshold

DTC B1935 1F

- Left Seat Back Heater Circuit Intermittent

DTC B2180 04

- Right Seat Back Heater Circuit Open

DTC B2180 0A

- Right Seat Back Heater Circuit Rate of Change Below Threshold

DTC B2180 0B

- Right Seat Back Heater Circuit Current Above Threshold

DTC B2180 0C

- Right Seat Back Heater Circuit Current Below Threshold

DTC B2180 0D

- Right Seat Back Heater Circuit Resistance Above Threshold

DTC B2180 0E

- Right Seat Back Heater Circuit Resistance Below Threshold

DTC B2180 1F

- Right Seat Back Heater Circuit Intermittent

Diagnostic Fault Information

Wednesday, November 20, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 369

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 369

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.

3. If all circuits test normal, replace the amplifier.

DTC Set By Radio UQA with U42

1. Ignition OFF, disconnect the X3 harness connector at the amplifier.

2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left front low level audio signal (+) - terminal 15

* Left front low level audio signal (-) - terminal 7

* Right front low level audio signal (+) - terminal 14

* Right front low level audio signal (-) - terminal 6

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the radio.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.

3. Ignition OFF, reconnect the X3 harness connector at the amplifier.

4. Disconnect the X2 harness connector at the rear seat audio (RSA) module.

5. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left rear low level audio signal (+) - terminal 1

* Left rear low level audio signal (-) - terminal 2

* Right rear low level audio signal (+) - terminal 3

* Right rear low level audio signal (-) - terminal 4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the rear seat audio (RSA) module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)

module.

6. Ignition OFF, reconnect the X2 harness connector at the rear seat audio (RSA) module.

7. Disconnect the X3 harness connector at the amplifier.

8. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left rear low level audio signal (+) - terminal 13

* Left rear low level audio signal (-) - terminal 5

* Right rear low level audio signal (+) - terminal 12

* Right rear low level audio signal (-) - terminal 4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the rear seat audio (RSA) module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)

module.

9. If all circuits test normal, replace the amplifier.

DTC Set By Radio UQA with Y91 and U42 or UQS and U42

1. Ignition OFF, disconnect the X3 and X4 harness connectors at the amplifier.

2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left front low level audio signal (+) - terminal 11 X3

* Left front low level audio signal (-) - terminal 12 X3

* Right front low level audio signal (+) - terminal 3 X3

* Right front low level audio signal (-) - terminal 4 X3

* Left rear low level audio signal (+) - terminal 11 X4

* Left rear low level audio signal (-) - terminal 12 X4

* Right rear low level audio signal (+) - terminal 3 X4

* Right rear low level audio signal (-) - terminal 4 X4

* Subwoofer low level audio signal (+) - terminal 5 X4

* Subwoofer low level audio signal (-) - terminal 6 X4

* Center Channel low level audio signal (+) - terminal 13 X4

* Center Channel low level audio signal (-) - terminal 14 X4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the radio.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.

3. If all circuits test normal, replace the amplifier.

Thursday, November 14, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 553

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 553

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

6. If all circuits test normal, replace the HSM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)

()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming

Rear Heated Seat Module

DTC B1925 or B2170 (w/o HP2 with Memory)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B1925 02

- Left Seat Cushion Heater Sensor Circuit Shorted to Ground

DTC B1925 05

- Left Seat Cushion Heater Sensor Circuit Shorted to Battery or Open

DTC B2170 02

- Right Seat Heater Cushion Sensor Circuit Shorted to Ground

DTC B2170 05

- Right Seat Heater Cushion Sensor Circuit Shorted to Battery or Open

Diagnostic Fault Information

Circuit/System Description

The heated seat temperature sensor that set this diagnostic trouble code (DTC) is located in the seat cushion just under the seat cover with the seat

heating element. The rear heated seat module (RHSM) supplies a 5 V reference voltage through the temperature sensor signal circuit and a ground

through the low reference circuit to the sensor. The RHSM monitors the voltage of the sensor signal circuit to determine the temperature of the seat.

The temperature sensor varies in resistance based on the temperature of the heating element causing the signal voltage to change. Once the seat

reaches the set temperature, the RHSM will then cycle the control circuit of the heating elements ON and OFF in order to maintain the desired seat

temperature based on the feedback voltage from the sensor.

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 547

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 547

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

6. If all circuits test normal, replace the HSM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)

()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming

B1935

DTC B1935 or B2180 (Dealer Installed)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B1935 04

- Left Seat Back Heater Circuit Open

DTC B1935 0A

- Left Seat Back Heater Circuit Rate of Change Below Threshold

DTC B1935 0B

- Left Seat Back Heater Circuit Current Above Threshold

DTC B1935 0C

- Left Seat Back Heater Circuit Current Below Threshold

DTC B1935 0D

- Left Seat Back Heater Circuit Resistance Above Threshold

DTC B1935 0E

- Left Seat Back Heater Circuit Resistance Below Threshold

DTC B1935 1F

- Left Seat Back Heater Circuit Intermittent

DTC B2180 04

- Right Seat Back Heater Circuit Open

DTC B2180 0A

- Right Seat Back Heater Circuit Rate of Change Below Threshold

DTC B2180 0B

- Right Seat Back Heater Circuit Current Above Threshold

DTC B2180 0C

- Right Seat Back Heater Circuit Current Below Threshold

DTC B2180 0D

- Right Seat Back Heater Circuit Resistance Above Threshold

DTC B2180 0E

- Right Seat Back Heater Circuit Resistance Below Threshold

DTC B2180 1F

- Right Seat Back Heater Circuit Intermittent

Diagnostic Fault Information

Tuesday, November 12, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 430

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 430

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.

3. If all circuits test normal, replace the amplifier.

DTC Set By Radio UQA with U42

1. Ignition OFF, disconnect the X3 harness connector at the amplifier.

2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left front low level audio signal (+) - terminal 15

* Left front low level audio signal (-) - terminal 7

* Right front low level audio signal (+) - terminal 14

* Right front low level audio signal (-) - terminal 6

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the radio.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.

3. Ignition OFF, reconnect the X3 harness connector at the amplifier.

4. Disconnect the X2 harness connector at the rear seat audio (RSA) module.

5. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left rear low level audio signal (+) - terminal 1

* Left rear low level audio signal (-) - terminal 2

* Right rear low level audio signal (+) - terminal 3

* Right rear low level audio signal (-) - terminal 4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the rear seat audio (RSA) module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)

module.

6. Ignition OFF, reconnect the X2 harness connector at the rear seat audio (RSA) module.

7. Disconnect the X3 harness connector at the amplifier.

8. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left rear low level audio signal (+) - terminal 13

* Left rear low level audio signal (-) - terminal 5

* Right rear low level audio signal (+) - terminal 12

* Right rear low level audio signal (-) - terminal 4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the rear seat audio (RSA) module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)

module.

9. If all circuits test normal, replace the amplifier.

DTC Set By Radio UQA with Y91 and U42 or UQS and U42

1. Ignition OFF, disconnect the X3 and X4 harness connectors at the amplifier.

2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left front low level audio signal (+) - terminal 11 X3

* Left front low level audio signal (-) - terminal 12 X3

* Right front low level audio signal (+) - terminal 3 X3

* Right front low level audio signal (-) - terminal 4 X3

* Left rear low level audio signal (+) - terminal 11 X4

* Left rear low level audio signal (-) - terminal 12 X4

* Right rear low level audio signal (+) - terminal 3 X4

* Right rear low level audio signal (-) - terminal 4 X4

* Subwoofer low level audio signal (+) - terminal 5 X4

* Subwoofer low level audio signal (-) - terminal 6 X4

* Center Channel low level audio signal (+) - terminal 13 X4

* Center Channel low level audio signal (-) - terminal 14 X4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the radio.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.

3. If all circuits test normal, replace the amplifier.

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 392

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 392

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)

module.

6. Ignition OFF, reconnect the X2 harness connector at the rear seat audio (RSA) module.

7. Disconnect the X2 harness connector at the amplifier.

8. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left rear low level audio signal (+) - terminal 15

* Left rear low level audio signal (-) - terminal 14

* Right rear low level audio signal (+) - terminal 16

* Right rear low level audio signal (-) - terminal 8

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the rear seat audio (RSA) module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)

module.

9. If all circuits test normal, replace the amplifier.

DTC Set by Audio Amplifier UQA

1. Ignition OFF, disconnect the X1 and X2 connectors at the amplifier.

2. Radio ON, test for less than 1 volt between the appropriate signal circuit terminal listed below and ground:

* Left front speaker output (+) - terminal 4 X2

* Left front speaker output (-) - terminal 3 X2

* Right front speaker output (+) - terminal 2 X2

* Right front low speaker output (-) - terminal 1 X2

* Left rear speaker output (+) - terminal 8 X2

* Left rear speaker output (-) - terminal 7 X2

* Right rear speaker output (+) - terminal 6 X2

* Right rear speaker output (-) - terminal 5 X2

* Left or rear subwoofer speaker output (+) - terminal 7 X1

* Left or rear subwoofer speaker output (-) - terminal 3 X1

* Right subwoofer speaker output (+) - terminal 6 X1

* Right subwoofer speaker output (-) - terminal 2 X1

瀚慖f greater than the specified range, test both circuits of the affected speaker for a short to voltage.

3. Radio OFF, test for infinite resistance between the appropriate signal circuit terminal listed below and ground:

* Left front speaker output (+) - terminal 4 X2

* Left front speaker output (-) - terminal 3 X2

* Right front speaker output (+) - terminal 2 X2

* Right front low speaker output (-) - terminal 1 X2

* Left rear speaker output (+) - terminal 8 X2

* Left rear speaker output (-) - terminal 7 X2

* Right rear speaker output (+) - terminal 6 X2

* Right rear speaker output (-) - terminal 5 X2

* Left or rear subwoofer speaker output (+) - terminal 7 X1

* Left or rear subwoofer speaker output (-) - terminal 3 X1

* Right subwoofer speaker output (+) - terminal 6 X1

* Right subwoofer speaker output (-) - terminal 2 X1

瀚慖f less than the specified value, test both circuits of the affected speaker for a short to ground.

4. If all circuits test normal, reconnect all harness connectors at the amplifier.

5. Ignition ON, radio ON, disconnect the appropriate speaker.

6. Test for 5.0-7.5 volts between the signal circuit terminals and ground.

瀚慖f less then the specified range test the circuit for an open/high resistance. If the circuit tests normal, replace the amplifier.

瀚慖f greater then the specified range test the circuit for a short to voltage. If the circuit tests normal, replace the amplifier.

7. If the circuit tests normal, replace the appropriate speaker.

DTC Set by Audio Amplifier UQA with Y91 or UQS

1. Ignition OFF, disconnect the X1 and X2 connectors at the amplifier.

2. Radio ON, test for less than 1 volt between the appropriate signal circuit terminal listed below and ground:

* Left front speaker output (+) - terminal 4 X2

* Left front speaker output (-) - terminal 5 X2

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 391

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 391

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)

module.

6. Ignition OFF, reconnect the X2 harness connector at the rear seat audio (RSA) module.

7. Disconnect the X3 harness connector at the amplifier.

8. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left rear low level audio signal (+) - terminal 13

* Left rear low level audio signal (-) - terminal 5

* Right rear low level audio signal (+) - terminal 12

* Right rear low level audio signal (-) - terminal 4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the rear seat audio (RSA) module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)

module.

9. If all circuits test normal, replace the amplifier.

DTC Set By Radio UQA with Y91 and U42 or UQS and U42

1. Ignition OFF, disconnect the X3 and X4 harness connectors at the amplifier.

2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left front low level audio signal (+) - terminal 11 X3

* Left front low level audio signal (-) - terminal 12 X3

* Right front low level audio signal (+) - terminal 3 X3

* Right front low level audio signal (-) - terminal 4 X3

* Left rear low level audio signal (+) - terminal 11 X4

* Left rear low level audio signal (-) - terminal 12 X4

* Right rear low level audio signal (+) - terminal 3 X4

* Right rear low level audio signal (-) - terminal 4 X4

* Subwoofer low level audio signal (+) - terminal 5 X4

* Subwoofer low level audio signal (-) - terminal 6 X4

* Center Channel low level audio signal (+) - terminal 13 X4

* Center Channel low level audio signal (-) - terminal 14 X4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the radio.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.

3. If all circuits test normal, replace the amplifier.

DTC Set By Radio UQA with Y91 and U42 or UQS and U42

1. Ignition OFF, disconnect the X3 and X4 harness connector at the amplifier.

2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left front low level audio signal (+) - terminal 11 X3

* Left front low level audio signal (-) - terminal 12 X3

* Right front low level audio signal (+) - terminal 3 X3

* Right front low level audio signal (-) - terminal 4 X3

* Subwoofer low level audio signal (+) - terminal 5 X4

* Subwoofer low level audio signal (-) - terminal 6 X4

* Center Channel low level audio signal (+) - terminal 13 X4

* Center Channel low level audio signal (-) - terminal 14 X4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the radio.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.

3. Ignition OFF, reconnect the X3 harness connector at the amplifier.

4. Disconnect the X2 harness connector at the rear seat audio (RSA) module.

5. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.

* Left rear low level audio signal (+) - terminal 1

* Left rear low level audio signal (-) - terminal 2

* Right rear low level audio signal (+) - terminal 3

* Right rear low level audio signal (-) - terminal 4

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the rear seat audio (RSA) module.