Wednesday, December 2, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2536

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2536

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Verify that DTCs P018C, P018D, P0231, P0232, or P023F are not set.

瀚慖f the DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic

Trouble Code (DTC) List - Vehicle).

2. Ignition OFF, disconnect the harness connector at the G12 fuel pump.

3. Ignition OFF, test for less than 5.0 ohm between the G12 fuel pump low reference circuit terminal A and ground.

瀚慖f greater than the specified range, test the G12 fuel pump low reference circuit for a high resistance. If the circuit tests normal, replace

the K27 fuel pump control module.

4. Ignition OFF, install a test lamp between the control circuit terminal D and the low reference circuit terminal A.

5. Ignition ON, command the Fuel Pump Relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between

the commanded states.

瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K27 fuel pump control

module.

瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the K27 fuel pump control module.

6. Perform the Fuel System Diagnosis (w/o FPCM) (See: Powertrain Management/Computers and Control Systems/Testing and

Inspection/Component Tests and General Diagnostics)Fuel System Diagnosis (FPCM) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics) to verify proper fuel pressure.

瀚慖f the fuel pressure is not normal, replace the G12 fuel pump

7. If all circuits test normal, replace the K27 fuel pump control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Tank Fuel Pump Module Replacement (2500 LWB - 43.5L (11.5 gal) Tank Rear) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (2500 LWB - 43.5L (11.5 Gal) Tank Rear))Fuel Tank

Fuel Pump Module Replacement (2500 LWB - 98.4L (26 gal) Tank Front) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (2500 LWB - 98.4L (26 Gal) Tank Front))Fuel Tank

Fuel Pump Module Replacement (1500 SWB - 98.4L (26 gal) Tank + E85) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (1500 SWB - 98.4L (26 Gal) Tank + E85))Fuel Tank

Fuel Pump Module Replacement (1500 Series) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and

Repair/Fuel Tank Fuel Pump Module Replacement (1500 Series))Fuel Tank Fuel Pump Module Replacement (1500 LWB - 117.3L (31 gal)

Tank + E85) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module

Replacement (1500 LWB - 117.3L (31 Gal) Tank + E85))

* Control Module References (See: Testing and Inspection/Programming and Relearning) for fuel pump control module replacement, setup,

and programming

P2636

DTC P2636

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provide an overview of each diagnostic category.