Showing posts with label (DTC) Type Definitions). Show all posts
Showing posts with label (DTC) Type Definitions). Show all posts

Sunday, November 29, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2450

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2450

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

Note: If other DTCs are set, diagnose those DTCs first.

1. Ignition ON, verify with a scan tool the Tap Up/Down Switch parameter displays ON in the Chassis Data list under BCM.

2. Ignition ON, verify with a scan tool the Tap Up/Down parameter displays UP when pressing the plus (+) switch and Down when pressing the

minus (-) switch.

3. Ignition ON, verify with a scan tool the Driver Shift Control parameter in the Transmission Data list changes from, Inactive to Active when

placing the automatic transmission shift lever in manual mode position.

4. Ignition ON, verify with a scan tool the Driver Shift Request Switch 1 displays NONE in the transmission data list.

5. Ignition ON, verify with a scan tool the Driver Shift Request Switch 1 displays Upshift when pressing the plus (+) switch and Downshift

when pressing the minus (-) switch.

6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

If no other DTCs are set, diagnosis is accomplished by testing for a condition on the CAN circuit. Refer to Scan Tool Does Not Communicate with

High Speed GMLAN Device (See: Powertrain Management/Computers and Control Systems/Information Bus/Testing and Inspection/Symptom

Related Diagnostic Procedures/Scan Tool Does Not Communicate with High Speed GMLAN Device).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

Control Module References (See: Testing and Inspection/Programming and Relearning)for control solenoid (w/body and TCM) valve assembly

replacement, setup, and programming.

P1762

DTC P1762

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptor

DTC P1762

- Transmission Mode Switch Signal Message

Circuit/System Description

The body control module (BCM) is constantly sending the engine control module (ECM) and transmission control module (TCM) serial data

messages with information regarding transmission mode switch activation. The TCM sets this code when it detects a discrepancy in the structure of

the message causing the signal message integrity to be questioned.

An intermittent fault in the controller area network (CAN) circuits will cause DTC P150C to set.

Conditions for Running the DTC

* The engine run time is greater than 5 seconds.

* No other CAN errors are present.

Conditions for Setting the DTC

* DTC P1762 is a Type B DTC.

* An intermittent fault in the CAN circuits.

Tuesday, November 17, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2164

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2164

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Observe the DTC information with a scan tool.

瀚慖f DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:

Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.

瀚慖f DTC P0602 resets, replace the K20 ECM.

2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.

瀚慖f a DTC failed this ignition, replace the K20 ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup

Fuel Pump Flow Control Module (FPCM)

DTC P0601-P0604, P0606, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory (ROM)

DTC P0602

- Control Module Not Programmed

DTC P0603

- Control Module Long Term Memory Reset

DTC P0604

- Control Module Random Access Memory (RAM)

DTC P0606

- Control Module Internal Performance

DTC P062F

- Control Module Long Term Memory Performance

Circuit/System Description

The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.

Conditions for Running the DTC

The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and

Monday, November 16, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2149

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2149

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Observe the DTC information with a scan tool.

瀚慖f DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:

Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.

瀚慖f DTC P0602 resets, replace the K20 ECM.

2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.

瀚慖f a DTC failed this ignition, replace the K20 ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup

2ML70 - Automatic Transmission

DTC P0601-P0606, P060B, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0601

- Transmission Control Module (TCM) Read Only Memory (ROM)

DTC P0602

- Transmission Control Module (TCM) Not Programmed

DTC P0603

- Transmission Control Module (TCM) Long Term Memory Reset

DTC P0604

- Transmission Control Module (TCM) Random Access Memory (RAM)

DTC P0606

- Transmission Control Module (TCM) Internal Performance

DTC P060B

- Control Module Analog to Digital Performance

DTC P062F

- Transmission Control Module (TCM) Long Term Memory Performance

Circuit/System Description

This is an internal fault detection of the transmission control module. This fault is handled inside the transmission control module and no external

circuits are involved. The transmission control module is part of the control solenoid valve assembly, and is not serviced separately.

Friday, November 6, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1893

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1893

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.

Circuit/System Verification

Test for the correct operation of the IMS. Refer to Transmission Internal Mode Switch Logic (See: Specifications/Mechanical

Specifications/Automatic Transmission/Transaxle/System Specifications/2ML70 - Automatic Transmission/Transmission Internal Mode Switch

Logic).

If the IMS operation matches the IMS logic table, the system if functioning normally.

Circuit/System Testing

1. Disconnect the IMS harness connector at the control solenoid (w/body and TCM) valve assembly. Ignition ON. The scan tool IMS A/B/C/P

parameter should display HI for all 4 signal circuits.

瀚慖f a signal circuit displays LOW, replace the control solenoid (w/body and TCM) valve assembly.

2. Connect a 3-amp fused jumper wire between each transmission range signal circuit at the control solenoid (w/body and TCM) valve assembly

and ground. With a scan tool, ensure that each signal circuit displays LOW when connected to ground.

瀚慖f a signal circuit remains HI when connected to ground, replace the control solenoid (w/body and TCM) valve assembly.

3. Connect the IMS harness connector to the control solenoid (w/body and TCM) valve assembly. Disconnect the IMS connector. The scan tool

IMS A/B/C/P parameter should display HI for all 4 signal circuits.

瀚慖f a signal circuit displays LOW, replace the IMS jumper harness.

4. Connect a 3-amp fused jumper wire between each transmission range signal circuit at the IMS connector harness and ground. With a scan

tool, ensure that each signal circuit displays LOW when connected to ground.

瀚慖f a signal circuit remains HI when connected to ground, replace the IMS harness.

瀚慖f a signal circuit other than the circuit being grounded displays LOW, replace the IMS harness.

瀚慖f all circuits test normal, replace the IMS.

Component Testing

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Important: Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and

Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection) for the following components before replacing

Monday, November 2, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1802

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1802

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.

瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: All modules must be powered down or misdiagnosis may result.

1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.

2. Ignition OFF, all vehicle systems OFF, this may take up to 2 minutes, test for less than 5 ohm between the low reference circuit terminal A

and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, verify the appropriate scan tool B52 HO2S parameter is approximately 450 mV.

瀚慖f less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the appropriate scan tool B52 HO2S

parameter is less than 60 mV.

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

5. If all circuits test normal, replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming

P0138

DTC P0131, P0132, P0137, P0138, P0151, P0152, P0157, or P0158

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

Wednesday, October 28, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1684

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1684

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the K27 fuel pump control module.

2. Ignition OFF, connect a test lamp between the control circuit terminal 13 and ground.

3. Ignition ON, command the fuel pump ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the

commanded states.

瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the K20 ECM.

4. If all circuits test normal, replace the K27 fuel pump control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM or fuel pump control module replacement, setup,

and programming

P0030

DTC P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141, P0155, or P0161

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0030

- HO2S Heater Control Circuit Bank 1 Sensor 1

DTC P0036

- HO2S Heater Control Circuit Bank 1 Sensor 2

DTC P0050

- HO2S Heater Control Circuit Bank 2 Sensor 1

DTC P0053

- HO2S Heater Resistance Bank 1 Sensor 1

DTC P0054

- HO2S Heater Resistance Bank 1 Sensor 2

DTC P0056

- HO2S Heater Control Circuit Bank 2 Sensor 2

DTC P0059

- HO2S Heater Resistance Bank 2 Sensor 1

DTC P0060

- HO2S Heater Resistance Bank 2 Sensor 2

DTC P0135

- HO2S Heater Performance Bank 1 Sensor 1

DTC P0141

- HO2S Heater Performance Bank 1 Sensor 2

Saturday, January 25, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1261

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1261



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



Note: If you can hear an engine knock, repair the engine mechanical condition before proceeding with this diagnostic. Refer to Symptoms - Engine



Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine



Mechanical).



1. Ignition ON, observe the DTC information with a scan tool. DTC P0335, P0336, or P0338 should not be set.



瀚慖f DTC P0335, P0336, or P0338 is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code



Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for diagnosis of DTC P0335, P0336, or P0338.



2. Clear the DTCs with a scan tool.



3. Turn OFF the ignition for 30 s.



4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



瀚慖f DTC P0324 failed this ignition, replace the K20 ECM.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and



programming



P0326



DTC P0326, P0327, P0328, P0331, P0332, or P0333 (LAU)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0326



- Knock Sensor System Performance Bank 1



DTC P0327



- Knock Sensor Circuit Low Voltage Bank 1



DTC P0328



- Knock Sensor Circuit High Voltage Bank 1



DTC P0331



- Knock Sensor System Performance Bank 2



DTC P0332



- Knock Sensor Circuit Low Voltage Bank 2



DTC P0333



- Knock Sensor Circuit High Voltage Bank 2



Circuit/System Description



The knock sensor is a piezoelectric device that produces an AC voltage of different amplitude and frequency depending on the level of engine



mechanical vibration. The knock sensor system monitors the knock sensor in order to determine if detonation or spark knock is present. If the



knock sensor system determines that excessive knock is present, the engine control module (ECM) retards the spark timing based on the signal



from the knock sensor system. The knock sensor produces an AC signal when specific frequencies are detected. The ECM then retards the timing

Monday, December 16, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1376

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1376



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ignition ON, command the EVAP purge solenoid to 50 percent with a scan tool. You should hear an audible click.



2. Engine operating, observe the scan tool EVAP Purge Solenoid Circuit Test Status parameters. Verify the parameters display OK or Not Run.



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, disconnect the harness connector at the Q12 EVAP purge solenoid.



2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal 1 and ground.



瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests



normal and the ignition voltage circuit fuse is open, test all components connected to the ignition voltage circuit and replace as necessary.



3. Connect a test lamp between the control circuit terminal 2 and the ignition voltage circuit terminal 1.



Note: The control circuit for the EVAP purge solenoid is pulled-up to voltage within the ECM, 2.6-4.6 V on the control circuit is normal.



4. Command the EVAP purge solenoid to 50 percent and then to 0 percent with a scan tool. The test lamp should illuminate or flash and then go



OFF.



瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.



瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace



the K20 ECM.



5. Test for 2.6-4.6 V between the control circuit terminal 2 and the ECM housing.



瀚慖f the voltage is not within the specified range, replace the K20 ECM.



6. If all circuits test normal, test or replace the Q12 EVAP purge solenoid.



Component Testing



1. Ignition OFF, disconnect the harness connector at the EVAP purge solenoid. Test for 15-20 ohm between the terminals of the EVAP purge



solenoid.



瀚慖f not within the specified range, replace the Q12 EVAP purge solenoid.



2. Measure the resistance between each terminal of the EVAP purge solenoid and the EVAP purge solenoid housing. The DMM should display



O.L.



瀚慖f less than the specified value, replace the Q12 EVAP purge solenoid.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Evaporative Emission Canister Purge Solenoid Valve Replacement (LF1) (See: Powertrain Management/Emission Control



Systems/Evaporative Emissions System/Canister Purge Solenoid/Service and Repair)Evaporative Emission Canister Purge Solenoid Valve



Replacement (LAU) (See: Powertrain Management/Emission Control Systems/Evaporative Emissions System/Canister Purge



Solenoid/Service and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P0461



DTC P0461-P0464, P2066, P2067, or P2068



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.

Monday, December 9, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1598

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1598



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Verify the transmission fluid level, color and odor is correct.



2. Operate the vehicle to induce a shift from fifth to sixth gear while observing the following scan tool parameters. The scan tool parameters has



to change the proper value referring to the current gear, compare the proper values with: Transmission System Description and Operation



(M36 and MXE) (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/AF40-6 - Automatic



Transmission/Transmission System Description and Operation (M36 and MXE)). Perform this action 2 times.



* Clutch Pressure Control Solenoid Valve 1 Current



* Clutch Pressure Control Solenoid Valve 2 Current



* Clutch Pressure Control Solenoid Valve 3 Current



* Brake Band Pressure Control Solenoid Valve Current



* Shift Solenoid Valve 1



* Shift Solenoid Valve 2



瀚慖f the scan tool parameter does not change the proper value and no other DTCs than P0729, P0731, P0732, P0733, P0734, P0735, P0736,



P0780, P1731 are set, go to Circuit/System Testing.



瀚慖f any other DTC is set, diagnose that DTC first.



Circuit/System Testing



Dynamic Test



1. Perform the line pressure check. Refer to Line Pressure Check (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/AF40-6 - Automatic Transmission/Line Pressure



Check).



2. Perform the transmission fluid check. Refer to Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/AF40-6 - Automatic Transmission/Transmission



Fluid Level and Condition Check).



3. If all circuits test normal, replace the K71 Transmission Control Module. Verify the DTC does not reset.



瀚慖f the DTC resets replace the control valve body.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Control valve body replacement-Refer to Control Valve Body Replacement (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Valve Body/Service and Repair/AF40-6 - Automatic Transmission/Control Valve Body Replacement) for



replacement, setup, and programming.



* TCM-Refer to Control Module References (See: Testing and Inspection/Programming and Relearning) for replacement, setup, and



programming.



* Perform the Transmission Adaptive Functions (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and



Operation/AF40-6 - Automatic Transmission/Transmission Adaptive Functions).



P0733



DTC P0733



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptor



DTC P0733



- 3rd Gear Ratio Incorrect



Diagnostic Fault Information

Sunday, December 8, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1431

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1431



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information



Circuit/System Verification



Engine ON, while rotating the steering wheel to both steering stops, observe the scan tool Cruise Control Switch parameter while pressing each of



the cruise control switches. The parameter should toggle between On, Off, Resume, Set, and Cancel as the applicable switch is pressed.



Circuit/System Testing



1. Ignition OFF, disconnect the harness connector at the S70L steering wheel control switch-left.



2. Ignition ON, test for B+ between the B+ circuit terminal 1 and ground.



瀚慖f less than the specified value, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9



BCM.



3. Test for B+ between the B+ circuit terminal 1 and the signal circuit terminal 2.



瀚慖f less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace



the K9 BCM.



4. Ignition OFF, disconnect the X1 harness connector at the K9 BCM.



5. Test for infinite resistance between the signal circuit terminal 3 and ground.



瀚慖f less than the specified value, test the signal circuit for a short to ground.



6. If all circuits test normal, test or replace the S70L steering wheel control switch-left.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Cruise Control Switch Replacement (See: Cruise Control/Cruise Control Switch/Service and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning)for BCM replacement, setup, and programming



P0568



DTC P0564, P0567, or P0568



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions)provides an overview of each diagnostic category.



DTC Descriptors



DTC P0564



- Cruise Control Multifunction Switch Circuit



DTC P0567



- Cruise Control Resume Switch Circuit



DTC P0568



- Cruise Control Set Switch Circuit



Diagnostic Fault Information

Sunday, December 1, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1495

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1495



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ignition ON, review the Failure Records when the DTC set. Verify the scan tool ECT Sensor parameter is less than 125掳C (257掳F).



瀚慖f greater than the specified range, refer to Engine Overheating (See: Engine, Cooling and Exhaust/Cooling System/Testing and



Inspection/Symptom Related Diagnostic Procedures/Engine Overheating).



2. Engine running, accessories OFF, measure and record the battery voltage at the battery terminals with a DMM. The voltage should be



between 12.6-15.0 volts.



瀚慖f not within the specified range, or the charge indicator light is ON, refer to Charging System Test (See: Starting and Charging/Testing



and Inspection/Component Tests and General Diagnostics/Charging System Test).



3. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing



and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Transmission Fluid Level and Condition



Check) to verify correct fluid level and condition.



4. Perform the Transmission Fluid Cooler Flushing and Flow Test (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic



Transmission/Transmission Fluid Cooler Flushing and Flow Test) to verify proper transmission oil cooler flow.



5. Operate the vehicle within the conditions for running and setting the DTC until normal engine temperature is reached. Verify the scan tool



TCM Temperature parameter is less than 146掳C (295掳F).



瀚慖f greater than the specified range, inspect the transmission cooling system for obstructions to the airflow of the radiator or transmission



due to debris, kinked, or damaged transmission fluid lines, or damage to the transmission cooler. If all the items test normal, replace the



control solenoid valve assembly.



6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Repair Instructions



Important:



* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and



Inspection/Programming and Relearning) following all transmission related repairs.



* Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See:



Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General



Diagnostics/6T70/6T75 - Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,



and programming



P0638



DTC P0638, P2100-P2103, or P2119 (Without LF1, LFW)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0638



- Throttle Actuator Control (TAC) Command Performance



DTC P2100



- Throttle Actuator Control (TAC) Motor Control Circuit

Friday, November 8, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1415

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1415

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

* EL-48571 High Voltage Battery Pin Out Box

* EL-48900 HEV Safety Kit

Circuit/System Verification

Ignition ON, observe the scan tool Hybrid Battery 1-20 parameters. Each reading should be between 10-19 V and all readings should be within 1.5

V of each other.

Circuit/System Testing

Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.

Personal Protection Equipment (PPE) and proper procedures must be followed.

The High Voltage Disabling procedure will perform the following tasks:

* Identify how to disable high voltage.

* Identify how to test for the presence of high voltage.

* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures

must be followed.

Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:

* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.

* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.

- Visually and functionally inspect the gloves before use.

- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or

not.

Failure to follow the procedures exactly as written may result in serious injury or death.

1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().

2. Disconnect the X4 harness connector at the drive motor battery control module.

3. Connect the EL-48571 high voltage battery pin out box.

4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.

5. Each battery voltage reading should be between 10-19 V.

瀚慖f not within the specified range, replace the drive motor battery assembly.

6. Each battery voltage reading should be within 1.5 V of each other.

瀚慖f not within the specified range, replace the drive motor battery assembly.

7. If all circuits test normal, replace the drive motor generator battery control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Drive Motor Generator Battery Replacement and Shipping Preparation ()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module

replacement, setup and programming

P0B55

DTC P0B3C, P0B41, P0B46, P0B4B, P0B50, P0B55, P0B5A, P0B5F, P0B64, P0B69, P0B6E, P0B73, P0B78, P0B7D, P0B82, P0B87, P0B8C,

P0B91, P0B96, or P0B9B

Diagnostic Instructions

Thursday, November 7, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1354

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1354

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

* EL-48571 High Voltage Battery Pin Out Box

* EL-48900 HEV Safety Kit

Circuit/System Verification

Ignition ON, observe the scan tool Hybrid Battery 1-20 parameters. Each reading should be between 10-19 V and all readings should be within 1.5

V of each other.

Circuit/System Testing

Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.

Personal Protection Equipment (PPE) and proper procedures must be followed.

The High Voltage Disabling procedure will perform the following tasks:

* Identify how to disable high voltage.

* Identify how to test for the presence of high voltage.

* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures

must be followed.

Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:

* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.

* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.

- Visually and functionally inspect the gloves before use.

- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or

not.

Failure to follow the procedures exactly as written may result in serious injury or death.

1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().

2. Disconnect the X4 harness connector at the drive motor battery control module.

3. Connect the EL-48571 high voltage battery pin out box.

4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.

5. Each battery voltage reading should be between 10-19 V.

瀚慖f not within the specified range, replace the drive motor battery assembly.

6. Each battery voltage reading should be within 1.5 V of each other.

瀚慖f not within the specified range, replace the drive motor battery assembly.

7. If all circuits test normal, replace the drive motor generator battery control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Drive Motor Generator Battery Replacement and Shipping Preparation ()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module

replacement, setup and programming

P0B6E

DTC P0B3C, P0B41, P0B46, P0B4B, P0B50, P0B55, P0B5A, P0B5F, P0B64, P0B69, P0B6E, P0B73, P0B78, P0B7D, P0B82, P0B87, P0B8C,

P0B91, P0B96, or P0B9B

Diagnostic Instructions

Wednesday, November 6, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1262

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1262

(DTC) Type Definitions)

Circuit/System Verification

1. Clear the DTC information.

2. Ignition OFF for 1 minute.

3. Operate the vehicle under the Conditions for Running the DTC.

4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,

P0BDE, P0BE1, P0BE2 AND P0BE3.

Circuit/System Testing

Program the PIM with the latest software version and recheck for DTCs.

If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.

P0BDD

DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0AEE

- Drive Motor Inverter Temperature Sensor 1 Performance

DTC P0AEF

- Drive Motor Inverter Temperature Sensor 1 Circuit Low Voltage

DTC P0AF0

- Drive Motor Inverter Temperature Sensor 1 Circuit High Voltage

DTC P0AF3

- Drive Motor Inverter Temperature Sensor 2 Performance

DTC P0AF4

- Drive Motor Inverter Temperature Sensor 2 Circuit Low Voltage

DTC P0AF5

- Drive Motor Inverter Temperature Sensor 2 Circuit High Voltage

DTC P0BD2

- Drive Motor Inverter Temperature Sensor 3 Performance

DTC P0BD3

- Drive Motor Inverter Temperature Sensor 3 Circuit Low Voltage

DTC P0BD4

- Drive Motor Inverter Temperature Sensor 3 Circuit High Voltage

DTC P0BD7

- Drive Motor Inverter Temperature Sensor 4 Performance

DTC P0BD8

- Drive Motor Inverter Temperature Sensor 4 Circuit Low Voltage

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1225

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1225

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

DT-48493 Jumper Harness, 24 terminal

Circuit/System Verification

P0A2B and P0A31

1. Allow the vehicle to cool to ambient temperature by leaving the ignition OFF for 6 or more hours.

2. Ignition ON, observe Motor 1 temperature, Motor 2 temperature, and phase U, V, W inverter temperature scan tool parameters.

瀚慣he Motor 1 Temperature, Motor 2 Temperature, and phase U, V, W inverter temperature parameters should be within 28掳C (50掳F) of

each other and ambient temperature.

P0A2C, P0A2D, P0A32, and P0A33

Ignition ON, observe the MCM motor temperature scan tool parameter.

The motor temperature parameter should be between 0.29V and 4.42V.

Circuit/System Testing

1. Ignition OFF, disconnect the transmission X176 24-way harness connector.

Important: The ignition must be ON to test the low reference circuit. Other DTCs will set with the X176 connector disconnected.

2. Ignition ON, test the vehicle harness side for less than 8 ohms between the low reference circuit terminal and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the PIM.

3. Ignition ON, verify the scan tool motor temperature sensor parameter is greater than 4.42V.

瀚慖f less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the PIM.

4. Install a 3-amp fused jumper wire between the signal circuit terminal and the low reference circuit terminal. Verify the scan tool motor

temperature sensor parameter is less than 0.29V.

Important: If a short to voltage is found, test the motor temperature sensor for damage.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal,

replace the PIM.

5. Connect the DT-48493 to the X176 transmission 24-way connector at the transmission. Measure and record the resistance between the sensor

signal and low reference terminals. Compare the actual sensor and circuit resistance to the expected sensor resistance. Refer to Temperature

Versus Resistance ().

瀚慖f the resistance is near the expected value, test the transmission internal harness signal circuit for a short to ground. If the circuit tests

normal, replace the drive motor w/generator.

瀚慖f the resistance is not near the expected value, test the transmission internal harness signal and low reference circuits for an open or

shorted together condition. If the circuits test normal, replace the drive motor w/generator.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming

* Transmission Control Wiring Harness Extension Harness Removal (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Service and Repair/Overhaul/2ML70 - Automatic Transmission/5. Transmission Control Wiring Harness Extension

Harness Removal)

* Drive Motor with Generator Assembly Removal - 1st Position (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Service and Repair/Overhaul/2ML70 - Automatic Transmission/8. Drive Motor with Generator Assembly Removal -

1st Position)

* Drive Motor with Generator Assembly Removal - 2nd Position (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Service and Repair/Overhaul/2ML70 - Automatic Transmission/13. Drive Motor with Generator Assembly Removal

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1214

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1214

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Verify with the scan tool that the BCM is reading the voltage correctly.

Circuit/System Testing

1. Turn the Ignition to ON.

2. Connect a DMM to the 14 volt battery.

3. Use the APM Low Voltage Control to turn on the APM 14 volt system. Vary the voltage setpoint with the scan tool ensuring that the DMM

tracks the commanded voltage.

瀚慖f the Low Voltage Control fails, replace the APM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for APM replacement, setup, and programming.

P0A9C

DTC P0A9C-P0A9E, P0AC6-P0AC8, P0ACB-P0ACD, P0AE9, P0AEA, or P0AEB

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0A9C

- Hybrid Battery 1 Temperature Sensor Performance

DTC P0A9D

- Hybrid Battery 1 Temperature Sensor Circuit Low Voltage

DTC P0A9E

- Hybrid Battery 1 Temperature Sensor Circuit High Voltage

DTC P0AC6

- Hybrid Battery 2 Temperature Sensor Performance

DTC P0AC7

- Hybrid Battery 2 Temperature Sensor Circuit Low Voltage

DTC P0AC8

- Hybrid Battery 2 Temperature Sensor Circuit High Voltage

DTC P0ACB

- Hybrid Battery 3 Temperature Sensor Performance

DTC P0ACC

- Hybrid Battery 3 Temperature Sensor Circuit Low Voltage

DTC P0ACD

- Hybrid Battery 3 Temperature Sensor Circuit High Voltage

DTC P0AE9

- Hybrid Battery 4 Temperature Sensor Performance

Sunday, November 3, 2019

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1994

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1994

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.

Circuit/System Verification

Test for the correct operation of the IMS. Refer to Transmission Internal Mode Switch Logic (See: Specifications/Mechanical

Specifications/Automatic Transmission/Transaxle/System Specifications/2ML70 - Automatic Transmission/Transmission Internal Mode Switch

Logic).

If the IMS operation matches the IMS logic table, the system if functioning normally.

Circuit/System Testing

1. Disconnect the IMS harness connector at the control solenoid (w/body and TCM) valve assembly. Ignition ON. The scan tool IMS A/B/C/P

parameter should display HI for all 4 signal circuits.

锟斤拷If a signal circuit displays LOW, replace the control solenoid (w/body and TCM) valve assembly.

2. Connect a 3-amp fused jumper wire between each transmission range signal circuit at the control solenoid (w/body and TCM) valve assembly

and ground. With a scan tool, ensure that each signal circuit displays LOW when connected to ground.

锟斤拷If a signal circuit remains HI when connected to ground, replace the control solenoid (w/body and TCM) valve assembly.

3. Connect the IMS harness connector to the control solenoid (w/body and TCM) valve assembly. Disconnect the IMS connector. The scan tool

IMS A/B/C/P parameter should display HI for all 4 signal circuits.

锟斤拷If a signal circuit displays LOW, replace the IMS jumper harness.

4. Connect a 3-amp fused jumper wire between each transmission range signal circuit at the IMS connector harness and ground. With a scan

tool, ensure that each signal circuit displays LOW when connected to ground.

锟斤拷If a signal circuit remains HI when connected to ground, replace the IMS harness.

锟斤拷If a signal circuit other than the circuit being grounded displays LOW, replace the IMS harness.

锟斤拷If all circuits test normal, replace the IMS.

Component Testing

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Important: Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and

Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection) for the following components before replacing

Saturday, November 2, 2019

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1903

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1903

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.

锟斤拷If a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: All modules must be powered down or misdiagnosis may result.

1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.

2. Ignition OFF, all vehicle systems OFF, this may take up to 2 minutes, test for less than 5 ohm between the low reference circuit terminal A

and ground.

锟斤拷If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, verify the appropriate scan tool B52 HO2S parameter is approximately 450 mV.

锟斤拷If less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

锟斤拷If greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the appropriate scan tool B52 HO2S

parameter is less than 60 mV.

锟斤拷If greater than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

5. If all circuits test normal, replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming

P0138

DTC P0131, P0132, P0137, P0138, P0151, P0152, P0157, or P0158

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

Friday, November 1, 2019

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1785

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1785

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the K27 fuel pump control module.

2. Ignition OFF, connect a test lamp between the control circuit terminal 13 and ground.

3. Ignition ON, command the fuel pump ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the

commanded states.

锟斤拷If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

锟斤拷If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the K20 ECM.

4. If all circuits test normal, replace the K27 fuel pump control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM or fuel pump control module replacement, setup,

and programming

P0030

DTC P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141, P0155, or P0161

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0030

- HO2S Heater Control Circuit Bank 1 Sensor 1

DTC P0036

- HO2S Heater Control Circuit Bank 1 Sensor 2

DTC P0050

- HO2S Heater Control Circuit Bank 2 Sensor 1

DTC P0053

- HO2S Heater Resistance Bank 1 Sensor 1

DTC P0054

- HO2S Heater Resistance Bank 1 Sensor 2

DTC P0056

- HO2S Heater Control Circuit Bank 2 Sensor 2

DTC P0059

- HO2S Heater Resistance Bank 2 Sensor 1

DTC P0060

- HO2S Heater Resistance Bank 2 Sensor 2

DTC P0135

- HO2S Heater Performance Bank 1 Sensor 1

DTC P0141

- HO2S Heater Performance Bank 1 Sensor 2

Monday, October 28, 2019

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1415

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1415

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

* EL-48571 High Voltage Battery Pin Out Box

* EL-48900 HEV Safety Kit

Circuit/System Verification

Ignition ON, observe the scan tool Hybrid Battery 1-20 parameters. Each reading should be between 10-19 V and all readings should be within 1.5

V of each other.

Circuit/System Testing

Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.

Personal Protection Equipment (PPE) and proper procedures must be followed.

The High Voltage Disabling procedure will perform the following tasks:

* Identify how to disable high voltage.

* Identify how to test for the presence of high voltage.

* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures

must be followed.

Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:

* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.

* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.

- Visually and functionally inspect the gloves before use.

- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or

not.

Failure to follow the procedures exactly as written may result in serious injury or death.

1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().

2. Disconnect the X4 harness connector at the drive motor battery control module.

3. Connect the EL-48571 high voltage battery pin out box.

4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.

5. Each battery voltage reading should be between 10-19 V.

锟斤拷If not within the specified range, replace the drive motor battery assembly.

6. Each battery voltage reading should be within 1.5 V of each other.

锟斤拷If not within the specified range, replace the drive motor battery assembly.

7. If all circuits test normal, replace the drive motor generator battery control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Drive Motor Generator Battery Replacement and Shipping Preparation ()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module

replacement, setup and programming

P0B55

DTC P0B3C, P0B41, P0B46, P0B4B, P0B50, P0B55, P0B5A, P0B5F, P0B64, P0B69, P0B6E, P0B73, P0B78, P0B7D, P0B82, P0B87, P0B8C,

P0B91, P0B96, or P0B9B

Diagnostic Instructions