2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2173
Actions Taken When the DTC Sets
* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.
* DTC P0607 is a Type C DTC.
* DTC P2610 is a Type B DTC.
Conditions for Clearing the MIL/DTC
* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.
* DTC P0607 is a Type C DTC.
* DTC P2610 is a Type B DTC.
Diagnostic Aids
Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set.
* Verify that the battery cables are clean and tight, and the battery is fully charged. Refer to Battery Inspection/Test (See: Starting and
Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* Verify the ECM ground circuits do not have an open or high resistance.
* Verify the ECM power circuits do not have an open, short to ground, or high resistance.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Observe the DTC information with a scan tool.
瀚慖f DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:
Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.
瀚慖f DTC P0602 resets, replace the K20 ECM.
2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.
瀚慖f a DTC failed this ignition, replace the K20 ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Showing posts with label Actions Taken When the DTC Sets. Show all posts
Showing posts with label Actions Taken When the DTC Sets. Show all posts
Tuesday, November 17, 2020
Sunday, December 22, 2019
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1434
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1434
Actions Taken When the DTC Sets
* The malfunction indicator lamp (MIL) will not illuminate.
* The cruise control system is disabled.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear after 40 malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Cruise Control Schematics (See: Cruise Control/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Description and Operation
Cruise Control Description and Operation (See: Cruise Control/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X1 (LF1) or X2 (LAU) harness connector at the K20 ECM.
2. Connect a test lamp between the appropriate signal circuit terminal listed below and ground.
* Terminal 57 (LF1)
* Terminal 52 (LAU)
3. Ignition ON, verify the test lamp turns ON and OFF when pressing and releasing the brake pedal.
瀚慖f the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the K9 BCM.
4. If all circuits test normal, replace the K20 ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning)for BCM or ECM, replacement, setup, and programming
P0573
DTC P0572 or P0573
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Monday, December 2, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 620
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 620
Actions Taken When the DTC Sets
The front fog lamps will not operate when the park lamps are ON and the front fog lamp switch is active.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Fog Lights Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System Diagram/Fog Lights Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the fog lamp relay.
2. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
瀚慖f the test lamp illuminates, test the control circuit for a short to voltage.
3. Verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the
B+ circuit fuse is open, test the control circuit terminal 87 for a short to ground. If the circuit tests normal, test or replace the fog lamp
relay.
4. Verify that a test lamp illuminates between the B+ circuit terminal 85 and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
5. Disconnect the harness connector at the appropriate fog lamp front.
6. Test for less than 5 ohm between the fog lamp front ground circuit terminal B and ground
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
7. Connect the harness connector at the fog lamp front.
8. Connect a 15 A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the fog lamp front is
activated.
瀚慖f the fog lamp front does not activate and the circuit fuse is good, test the control circuit for an open/high resistance. If the circuit tests
normal, test or replace the fog lamp front.
瀚慖f the fog lamp front does not activate and the circuit fuse is open, test the control circuit for a short to ground. If the circuit tests normal,
test or replace the fog lamp front.
9. Connect a test lamp between the B+ circuit terminal 85 and the control circuit terminal 86.
10. Command the Fog Lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded
Actions Taken When the DTC Sets
The front fog lamps will not operate when the park lamps are ON and the front fog lamp switch is active.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Fog Lights Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System Diagram/Fog Lights Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the fog lamp relay.
2. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
瀚慖f the test lamp illuminates, test the control circuit for a short to voltage.
3. Verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the
B+ circuit fuse is open, test the control circuit terminal 87 for a short to ground. If the circuit tests normal, test or replace the fog lamp
relay.
4. Verify that a test lamp illuminates between the B+ circuit terminal 85 and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
5. Disconnect the harness connector at the appropriate fog lamp front.
6. Test for less than 5 ohm between the fog lamp front ground circuit terminal B and ground
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
7. Connect the harness connector at the fog lamp front.
8. Connect a 15 A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the fog lamp front is
activated.
瀚慖f the fog lamp front does not activate and the circuit fuse is good, test the control circuit for an open/high resistance. If the circuit tests
normal, test or replace the fog lamp front.
瀚慖f the fog lamp front does not activate and the circuit fuse is open, test the control circuit for a short to ground. If the circuit tests normal,
test or replace the fog lamp front.
9. Connect a test lamp between the B+ circuit terminal 85 and the control circuit terminal 86.
10. Command the Fog Lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded
Sunday, November 17, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 288
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 288
Actions Taken When the DTC Sets
* The low beam headlamps are always ON in the AUTO position. The headlamp switch operates in all positions other than AUTO. The AUTO
headlamp defeat is inoperative.
* The low beam headlamps are always ON. The BCM disregards all headlamp switch inputs.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System
Diagram/Headlights/Daytime Running Lights (DRL) Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X2 harness connector at the BCM.
2. Connect a test lamp between B+ and the signal circuit terminal 17.
3. Turn the headlamp switch between the AUTO and AUTO disable positions. The test lamp should turn ON and OFF as the switch is cycled.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the
headlamp and panel dimmer switch.
瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel
dimmer switch.
4. Connect a test lamp between B+ and the signal circuit terminal 3.
5. Turn the headlamp switch to the ON and OFF positions. The test lamp should turn ON and OFF as the switch is cycled.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the
headlamp and panel dimmer switch.
瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel
dimmer switch.
6. If all circuits test normal, replace the BCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Headlamp Switch Replacement (Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service and Repair/Headlamp Switch
Replacement (Cadillac))Headlamp Switch Replacement (Except Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service
and Repair/Headlamp Switch Replacement (Except Cadillac))
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
Actions Taken When the DTC Sets
* The low beam headlamps are always ON in the AUTO position. The headlamp switch operates in all positions other than AUTO. The AUTO
headlamp defeat is inoperative.
* The low beam headlamps are always ON. The BCM disregards all headlamp switch inputs.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System
Diagram/Headlights/Daytime Running Lights (DRL) Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X2 harness connector at the BCM.
2. Connect a test lamp between B+ and the signal circuit terminal 17.
3. Turn the headlamp switch between the AUTO and AUTO disable positions. The test lamp should turn ON and OFF as the switch is cycled.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the
headlamp and panel dimmer switch.
瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel
dimmer switch.
4. Connect a test lamp between B+ and the signal circuit terminal 3.
5. Turn the headlamp switch to the ON and OFF positions. The test lamp should turn ON and OFF as the switch is cycled.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the
headlamp and panel dimmer switch.
瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel
dimmer switch.
6. If all circuits test normal, replace the BCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Headlamp Switch Replacement (Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service and Repair/Headlamp Switch
Replacement (Cadillac))Headlamp Switch Replacement (Except Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service
and Repair/Headlamp Switch Replacement (Except Cadillac))
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
Monday, November 11, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 289
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 289
Actions Taken When the DTC Sets
* The low beam headlamps are always ON in the AUTO position. The headlamp switch operates in all positions other than AUTO. The AUTO
headlamp defeat is inoperative.
* The low beam headlamps are always ON. The BCM disregards all headlamp switch inputs.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System
Diagram/Headlights/Daytime Running Lights (DRL) Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X2 harness connector at the BCM.
2. Connect a test lamp between B+ and the signal circuit terminal 17.
3. Turn the headlamp switch between the AUTO and AUTO disable positions. The test lamp should turn ON and OFF as the switch is cycled.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the
headlamp and panel dimmer switch.
瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel
dimmer switch.
4. Connect a test lamp between B+ and the signal circuit terminal 3.
5. Turn the headlamp switch to the ON and OFF positions. The test lamp should turn ON and OFF as the switch is cycled.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the
headlamp and panel dimmer switch.
瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel
dimmer switch.
6. If all circuits test normal, replace the BCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Headlamp Switch Replacement (Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service and Repair/Headlamp Switch
Replacement (Cadillac))Headlamp Switch Replacement (Except Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service
and Repair/Headlamp Switch Replacement (Except Cadillac))
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
Actions Taken When the DTC Sets
* The low beam headlamps are always ON in the AUTO position. The headlamp switch operates in all positions other than AUTO. The AUTO
headlamp defeat is inoperative.
* The low beam headlamps are always ON. The BCM disregards all headlamp switch inputs.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System
Diagram/Headlights/Daytime Running Lights (DRL) Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X2 harness connector at the BCM.
2. Connect a test lamp between B+ and the signal circuit terminal 17.
3. Turn the headlamp switch between the AUTO and AUTO disable positions. The test lamp should turn ON and OFF as the switch is cycled.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the
headlamp and panel dimmer switch.
瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel
dimmer switch.
4. Connect a test lamp between B+ and the signal circuit terminal 3.
5. Turn the headlamp switch to the ON and OFF positions. The test lamp should turn ON and OFF as the switch is cycled.
瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the
headlamp and panel dimmer switch.
瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel
dimmer switch.
6. If all circuits test normal, replace the BCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Headlamp Switch Replacement (Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service and Repair/Headlamp Switch
Replacement (Cadillac))Headlamp Switch Replacement (Except Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service
and Repair/Headlamp Switch Replacement (Except Cadillac))
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
Subscribe to:
Posts (Atom)