Showing posts with label Diagnostic Fault Information. Show all posts
Showing posts with label Diagnostic Fault Information. Show all posts

Sunday, December 6, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2633

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2633

Diagnostic Fault Information

Circuit/System Description

The PTLAN serial data circuits are serial data buses used to communicate information between the control modules. The PTLAN serial data

circuits also connect directly to the data link connector (DLC) for programming purposes. If this serial data system is inoperative the modules will

still communicate with the scan tool due to other serial data systems but not with each other. Communication with the scan tool for the modules on

the PTLAN bus is through the serial data gateway module (SDGM) on the HSGMLAN serial data system.

Conditions for Running the DTCs

* Supply voltage to the modules are in the normal operating range.

* The ignition switch in any position other than START.

Conditions for Setting the DTC

The module setting the DTC has attempted to establish communications on the PTLAN serial data circuits more than 3 times.

Action Taken When the DTCs Sets

* The module suspends all message transmission.

* The MIL and battery indicators will illuminate, along with several DIC messages.

* The vehicle may continue to run for several minutes, then will stall and not start.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction.

Diagnostic Aids

* Sometimes, while diagnosing a specific customer concern or after a repair, you may notice a history U-code present. However, there is no

associated "current" or "active" status. Loss-of- communication U-codes such as these can set for a variety of reasons. Many times, they're

transparent to the vehicle operator and technician, and/or have no associated symptoms. Eventually, they will erase themselves automatically

after a number of fault-free ignition cycles. This condition would most likely be attributed to one of these scenarios:

- A control module on the data communication circuit was disconnected while the communication circuit is awake.

- Power to one or more modules was interrupted during diagnosis

- A low battery condition was present, so some control modules stop communicating when battery voltage drops below a certain threshold.

- Battery power was restored to the vehicle and control modules on the communication circuit did not all re-initialize at the same time.

- If a loss-of-communication U-code appears in history for no apparent reason, it is most likely associated with one of the scenarios above.

These are all temporary conditions and should never be interpreted as an intermittent fault, causing you to replace a part.

* Do not replace a control module reporting a U code. The U code identifies which control module needs to be diagnosed for a communication

issue.

* Communication may be available between the BCM and the scan tool with the Powertrain High Speed GMLAN serial data system

inoperative. This condition is due to the BCM using both the high and low speed GMLAN systems.

* The engine will not start when there is a total malfunction of the Powertrain High Speed GMLAN serial data bus.

Reference Information

Schematic Reference

* Data Communication Schematics (See: Powertrain Management/Computers and Control Systems/Information Bus/Diagrams/Electrical

Diagrams)

* Control Module References (See: Testing and Inspection/Programming and Relearning)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Data Link Communications Description and Operation (See: Powertrain Management/Computers and Control Systems/Information

Bus/Description and Operation)

Electrical Information Reference

Thursday, November 26, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2383

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2383

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

The clutch pressure (PC) solenoid 3 is part of the control solenoid valve assembly which has no serviceable parts. The normally high clutch PC

solenoid 3 regulates and directs the clutch PC solenoid 3 oil pressure to the 4-5-6 clutch regulator valve and 4-5-6 clutch boost valve. Increasing

clutch PC solenoid 3 oil pressure increases oil pressure to the 4-5-6 clutch assembly. The TCM varies the current to the PC solenoid 3 through a

low side driver. Decreasing the current to the clutch PC solenoid 3 increases clutch PC solenoid 3 oil pressure by closing OFF the solenoid exhaust

port. Increasing the current to the clutch PC solenoid 3, decreases clutch PC solenoid 3 oil pressure by opening the solenoid exhaust port. Clutch

PC solenoid 3 power is supplied by the TCM through a high side driver (HSD). The HSD protects the circuit and components from excessive

current flow. If excessive current flow is detected, the HSD will turn OFF. When the fault is corrected the HSD will reset.

Conditions for Running the DTC

P0969, P0970, or P0971

* DTCs P0969, P0970, or P0971 have not set this ignition.

* The ignition voltage is 8.6 volts or greater.

* The engine speed is 500 RPM or greater for 5 seconds.

* The clutch PC solenoid 3 is commanded ON.

Conditions for Setting the DTC

P0969

The TCM detects an internal electrical malfunction on the clutch PC solenoid 3 control circuit where the measured PC solenoid 3 current does not

equal the commanded clutch PC solenoid 3 current for 5 seconds.

P0970

The TCM detects a short to ground on the clutch PC solenoid 3 control circuit for 1 second.

P0971

The TCM detects an open or short to voltage on the Clutch PC solenoid 3 control circuit for 1 second.

Action Taken When the DTC Sets

P0969

* DTC P0969 is a Type C DTCs.

* The TCM freezes transmission adaptive functions.

P0970

* DTC P0970 is a Type A DTC.

* The TCM defaults the transmission to a limited shift pattern utilizing 2 forward gears and reverse gear based on the default detected.

* The TCM forces HSD1 OFF.

* The TCM forces TCC OFF.

* The TCM freezes transmission adaptive functions.

* The TCM commands maximum line pressure.

* The TCM enables Torque management.

* The TCM inhibits TAP Up/Down function.

Monday, November 16, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2143

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2143

Diagnostic Fault Information

Circuit/System Description

The TCC Brake signal circuit is a high voltage input to the body control module (BCM), engine control module (ECM), transmission control

module (TCM), Power Take Off (PTO) module (if equipped) and Trailer Brake controller (if equipped). The BCM monitors the stop lamp switch

circuit to detect when the brake pedal has been applied. The ECM monitors the TCC Brake signal to determine when the brake pedal is applied.

When the brake pedal is applied, the BCM sends a serial data message to the ECM indicating that the brake pedal has been applied. The ECM

senses a high voltage signal on the brake switch signal circuit when the stop lamp switch is closed.

Conditions for Running the DTC

* The engine is running.

* Battery voltage is greater than 11.5 volts.

Conditions for Setting the DTC

P0572

The ECM detects a low voltage signal on the TCC brake signal circuit for more than 2 seconds when the serial data message from the BCM

indicates the brakes are applied. The ECM sets the DTC when the condition has been detected 8 out of 10 times.

P0573

The ECM detects a high voltage signal on the TCC brake signal circuit for more than 2 seconds when the serial data message from the BCM

indicates the brakes are released. The ECM sets the DTC when the condition has been detected 8 out of 10 times.

Actions Taken When the DTC Sets

* The cruise control system becomes disabled.

* The malfunction indicator lamp (MIL) will not illuminate.

Conditions for Clearing the DTC

* The condition responsible for setting the DTC no longer exists.

* A history DTC will clear after 40 malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

* Cruise Control Schematics (See: Cruise Control/Diagrams/Electrical Diagrams)

* Exterior Lights Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System Diagram/Exterior Lights Schematics)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Cruise Control Description and Operation (See: Cruise Control/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Saturday, November 14, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2095

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2095

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

The engine cooling fan system consists of 2 electric cooling fans and 3 fan relays. The cooling fan relays are arranged in a series/parallel (S/P)

configuration. This allows the engine control module (ECM) to operate both fans together at low or high speeds using 2 fan control circuits. The

cooling fans receive positive voltage from the cooling fan relays, which receive battery positive voltage from the underhood fuse block. The

cooling fans are supplied a ground at G100 and G101.

Conditions for Running the DTC

* The system voltage is between 9-18 volts.

* The engine speed is greater than 400 RPM.

* DTCs P0480 and P0481 run continuously when the conditions above are met.

Conditions for Setting the DTC

* The commanded state of the ECM driver and the actual state of the control circuit do not match.

* The condition exists for greater than 5 seconds.

Action Taken When the DTC Sets

DTCs P0480 and P0481 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0480 and P0481 are Type B DTCs.

Diagnostic Aids

* The ECM has the capability of providing command to the fan relays even when a scan tool output control is being used. Always refer to the

fan control command parameters on the scan tool to know which fans are being commanded ON by the ECM.

* The scan tool cooling fan output control operates as follows:

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2088

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2088

Diagnostic Fault Information

Circuit/System Description

The fuel level sensor changes resistance in response to the fuel level. The engine control module (ECM) monitors the signal circuit of the fuel level

sensor and the type of fuel in order to determine the fuel level. For regular unleaded fuel the ECM monitors a constant signal. When the vehicle has

approximately 20% or greater ethanol for E85 fuel applications, the ECM controls a pulse cycle signal where it monitors the signal and calculates

the fuel level percentage only during the on pulse of approximately 100 ms.

When the fuel tank is full, the sensor resistance is low and the ECM senses a low signal voltage. When the fuel tank is empty, the sensor resistance

is high and the ECM senses a high signal voltage. The ECM uses the signal circuit of the fuel level sensor in order to calculate the percentage of

remaining fuel in the tank. The ECM sends the fuel level percentage via the serial data circuit to the instrument cluster in order to control the fuel

gauge.

Conditions for Running the DTC

* The ignition is ON, with the engine running.

* The system voltage is between 11-18 V.

Conditions for Setting the DTC

* The sensor output is greater than 3.5 V.

* The above condition is present for greater than 30 seconds.

Action Taken When the DTC Sets

* The fuel gauge defaults to empty.

* The low fuel indicator illuminates.

* The ECM records the operating conditions at the time that the diagnostic test fails. The ECM displays the failure information in the Failure

Records on the scan tool.

Conditions for Clearing the DTC

* The DTC becomes history when the conditions for setting the DTC are no longer present.

* The history DTC clears after 40 malfunction-free warm-up cycles.

Diagnostic Aids

A defective fuel level sensor most likely will not set DTC P0463. The sensor has a 500 ohm default resistor that will prevent it from meeting the

code setting criteria of this DTC. Look for problems in the wiring and in the inline and harness connectors at the sensor and ECM.

Reference Information

Schematic Reference

Instrument Cluster Schematics (See: Diagrams/Electrical Diagrams/Instrument Panel, Gauges and Warning Indicators/System Diagram/Instrument

Cluster Schematics)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Instrument Cluster Description and Operation (See: Instrument Panel, Gauges and Warning Indicators/Description and Operation/Instrument

Cluster)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Saturday, November 7, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1934

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1934

Diagnostic Fault Information

Circuit/System Description

The control module enables the appropriate fuel injector pulse for each cylinder. Ignition voltage is supplied to the fuel injectors. The control

module controls each fuel injector by grounding the control circuit via a solid state device called a driver. The control module monitors the status of

each driver.

Conditions for Running the DTC

* The engine is running.

* The ignition voltage is greater than 11 V.

* DTC P0201-P0208 runs continuously when the above conditions are met.

Conditions for Setting the DTC

The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 2 s.

Action Taken When the DTC Sets

DTCs P0201, P0202, P0203, P0204, P0205, P0206, P0207, and P0208 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0201, P0202, P0203, P0204, P0205, P0206, P0207, and P0208 are Type B DTCs.

Diagnostic Aids

Performing the Fuel Injector Diagnosis may help isolate an intermittent condition. Refer to Fuel Injector Diagnosis (CH47976) (See: Powertrain

Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)Fuel Injector Diagnosis (J39021 or Scan Tool) (See:

Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection).

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Fuel System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1929

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1929

Diagnostic Fault Information

Circuit/System Description

The control module enables the appropriate fuel injector pulse for each cylinder. Ignition voltage is supplied to the fuel injectors. The control

module controls each fuel injector by grounding the control circuit via a solid state device called a driver. The control module monitors the status of

each driver.

Conditions for Running the DTC

* The engine is running.

* The ignition voltage is greater than 11 V.

* DTC P0201-P0208 runs continuously when the above conditions are met.

Conditions for Setting the DTC

The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 2 s.

Action Taken When the DTC Sets

DTCs P0201, P0202, P0203, P0204, P0205, P0206, P0207, and P0208 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0201, P0202, P0203, P0204, P0205, P0206, P0207, and P0208 are Type B DTCs.

Diagnostic Aids

Performing the Fuel Injector Diagnosis may help isolate an intermittent condition. Refer to Fuel Injector Diagnosis (CH47976) (See: Powertrain

Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)Fuel Injector Diagnosis (J39021 or Scan Tool) (See:

Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection).

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Fuel System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Sunday, November 1, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1791

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1791

Diagnostic Fault Information

Circuit/System Description

The heated oxygen sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding

air with the oxygen content of the exhaust stream. When the engine is started, the control module operates in an Open Loop mode, ignoring the

HO2S signal voltage while calculating the air-to-fuel ratio. While the engine runs, the HO2S heats up and begins to generate a voltage within a

range of 0-1,275 mV. Once sufficient HO2S voltage fluctuation is observed by the control module, Closed Loop is entered. The control module

uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases toward 1,000 mV indicates a rich fuel mixture. An HO2S

voltage that decreases toward 0 mV indicates a lean fuel mixture.

The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed

Loop earlier and the control module to calculate the air-to-fuel ratio sooner.

Conditions for Running the DTC

P0133, P0153, P1133, or P1153

* DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128,

P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516,

P2101, P2119, P2135, P2176 are not set.

* The engine coolant temperature (ECT) is greater than 60掳C (140掳F).

* The intake air temperature (IAT) is warmer than -40掳C (-40掳F)

* The ignition 1 voltage is between 10-32 V.

* The fuel level is greater than 10 %.

* The engine run time is greater than 160 s.

* The engine speed is between 1,200-3,000 RPM.

* The barometric (BARO) pressure is greater than 70 kPa.

* The mass airflow (MAF) is between 20-55 g/s.

* The fuel system is in Closed Loop.

* The throttle position (TP) is greater than 5 %.

* The DTCs run once per drive cycle when the above conditions are met.

P013A P013C, P013E, or P014A

* Before the ECM can report DTC P013A, or P013C failed, DTCs P013E, P014A, P2270, and P2272 must run and pass.

* Before the ECM can report DTC P013E, or P014A failed, DTCs P2270 and P2272 must run and pass.

* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,

P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,

P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are

not set.

* The ignition 1 voltage is between 10-32 V.

* The learned heater resistance is valid.

* The fuel level is greater than 10 %.

* The engine run time is equal to or greater than 5 minutes.

* The accelerator pedal (APP) is steady.

* The torque converter clutch (TCC) is applied.

* The DTCs run once per ignition cycle, during decel fuel cut-off (DFCO), when the above conditions are met.

P013B P013D, P013F, or P014B

* Before the ECM can report DTC P013B, or P013D failed, DTCs P013A, P013C, P013E, P013F, P014A, P014B, P2270, P2271, P2272, and

P2273 must run and pass.

* Before the ECM can report DTC P013F, or P014B failed, DTCs P013A, P013C, P013E, P014A, P2270, P2271, P2272, and P2273 must run

and pass.

* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,

Saturday, October 31, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1753

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1753

Diagnostic Fault Information

Typical Scan Tool Data

Circuit Description

The manifold absolute pressure (MAP) sensor measures the pressure inside the intake manifold. Pressure in the intake manifold is affected by

engine speed, throttle opening, air temperature, and barometric pressure (BARO). A diaphragm within the MAP sensor is displaced by the pressure

changes that occur from the varying load and operating conditions of the engine. The sensor translates this action into electrical resistance. The

MAP sensor wiring includes 3 circuits. The engine control module (ECM) supplies a regulated 5 volts to the sensor on a 5-volt reference circuit.

The ECM supplies a ground on a low reference circuit. The MAP sensor provides a signal voltage to the ECM, relative to the pressure changes, on

the MAP sensor signal circuit. The ECM converts the signal voltage input to a pressure value.

Under normal operation the highest pressure that can exist in the intake manifold is equal to BARO. This occurs when the vehicle is operated at

wide-open throttle (WOT) or when the ignition is ON while the engine is OFF. Under these conditions, the ECM uses the MAP sensor to determine

the current BARO. The lowest manifold pressures occur when the vehicle is idling or decelerating. MAP can range from 10 kPa, when pressures

are low, to as much as 104 kPa when pressures are high, depending on the BARO. The ECM monitors the MAP sensor signal for pressure outside

of the normal range.

Conditions for Running the DTC

P0107

* DTCs P0641, P0651, P1516, P2101, P2125, P2135, P2138, P2176 are not set.

* The engine speed is greater than 400 RPM.

* The throttle angle is greater than 0 percent when the engine speed is less than 800 RPM.

OR

* The throttle angle is greater than 13 percent when the engine speed is greater than 800 RPM.

* This DTC runs continuously when the above conditions are met.

P0108

* DTCs P1516, P2101, P2125, P2135, P2138, P2176 are not set.

* The engine has been running for a period of time that is determined by the start-up engine coolant temperature (ECT). The time ranges from

8 seconds at less than -30掳C (-22掳F) to 3 seconds at greater than 30掳C (86掳F).

* The throttle angle is less than 1 percent when the engine speed is less than 1,200 RPM.

OR

* The throttle angle is less than 20 percent when the engine speed is greater than 1,200 RPM.

* This DTC runs continuously when the above conditions are met.

Conditions for Setting the DTC

P0107

The ECM detects that the MAP sensor voltage is less than 0.1 volt for more than 4 seconds.

P0108

The ECM detects that the MAP sensor voltage is more than 4.9 volts for greater than 4 seconds.

Action Taken When the DTC Sets

DTCs P0107 and P0108 are Type B DTCs.

Monday, March 30, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1587

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1587



Diagnostic Fault Information



Typical Scan Tool Data



Circuit/System Description



The output shaft sensor is a hall-effect type sensor. The sensor faces the output shaft machined teeth surface. As the output shaft rotates, the sensor



produces a signal frequency based on the machined surface of the output shaft. This signal is transmitted to the transmission control module (TCM).



The TCM uses the output shaft sensor signal in connection with the input speed sensor signal to control engine torque, shift timing, and lock-up.



Conditions for Running the DTC



P0722



* The ignition voltage is 10.2-15.5 V.



* The engine speed is greater than 400 RPM for 2 s.



* The transmission is not in emergency mode.



* TCM communication is normal.



* Driving in D range.



Conditions for Setting the DTC



P0722



* Deviation from calculated output speed is more than 300 RPM.



* No output speed sensor pulse while receiving pulses on the input speed sensor.



* No output speed sensor pulse when vehicle speed from ABS is more than 20 km/h (13 MPH) for 300 ms.



Action Taken When the DTC Sets



* DTC P0722 is Type A DTC.



* The TCM freezes transmission adaptive functions.



* The TCM turns OFF all solenoids.



* The TCM allows the vehicle after a stop to operate only in the second gear and "R" range.



Conditions for Clearing the DTC



* DTC P0722 is Type A DTC.



* Output speed is greater than 300 RPM for more than 70 s.



* Deviation from calculated output speed is less than 5% for more than 1 s.



Diagnostic Aids



* Damage or misalignment of the counter drive gear machined teeth surface may cause a speed sensor malfunction.



* Proper torque of the output shaft sensor mounting bolt is critical to proper output shaft sensor operation.



Reference Information



Schematic Reference



Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams/Electrical



Diagrams)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Wednesday, February 12, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 2041

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 2041



Diagnostic Fault Information



Circuit/System Description



The body control module (BCM) activates the serial data communication enable circuit when the ignition key is in ACC, ON or START. The serial



data communication enable circuit wakes up the engine control module (ECM) for serial data bus communication.



Conditions for Running the DTC



* The system voltage is between 9-16 volts.



* The vehicle power mode master requires serial data communication to occur.



Conditions for Setting the DTC



The BCM senses a short to ground on the serial data communication enable circuit.



Action Taken When the DTC Sets



* The output command is turned off while the malfunction is present.



* The modules use a default value for the missing parameters until the next ignition cycle.



* The module(s) is never signaled, therefore the specific subsystem(s) will not function.



* The vehicle will not start while the circuit is shorted to ground.



Conditions for Clearing the DTC



* A current DTC clears when the malfunction is no longer present.



* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.



Diagnostic Aids



* Use the DMM MIN/MAX function to capture/locate intermittent conditions.



* Short to ground will also set multiple history no communication codes for GMLAN high speed modules.



Reference Information



Schematic Reference



Data Communication Schematics (See: Powertrain Management/Computers and Control Systems/Information Bus/Diagrams/Electrical Diagrams)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Data Link Communications Description and Operation (See: Powertrain Management/Computers and Control Systems/Information



Bus/Description and Operation)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



Circuit/System Testing



Note: Use the schematic to determine which control modules are on the BCM communications enable circuit 22, X4.



1. Ignition OFF, disconnect the harness connector at the most easily accessible control module on the BCM communications enable circuit.



2. Ignition ON, retest for current DTCs. DTC U1814 should remain current.



瀚慖f the DTC becomes history, replace the control module.

Tuesday, December 17, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 95

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 95

Diagnostic Fault Information

Circuit/System Description

If a malfunction is detected, a DTC will be stored in non-volatile memory. During a frontal crash of sufficient force the inflatable restraint sensing

and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the driver steering wheel air bag. The

SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage.

There are 2 shorting bars used within each connector which will short together both driver steering wheel air bag stage 1 high circuit and driver

steering wheel air bag stage 1 low circuit and both driver steering wheel air bag stage 2 high circuit and driver steering wheel air bag stage 2 low

circuit when the connector is disconnected. This will help to prevent unwanted deployment of the air bag during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0012 01 Stage 1 or B0013 01 Stage 2

The driver steering wheel air bag high and/or low circuit is shorted to voltage for 120 milliseconds.

B0012 02 Stage 1 or B0013 02 Stage 2

The driver steering wheel air bag high and/or low circuit is shorted to ground for 120 milliseconds.

B0012 04 Stage 1 or B0013 04 Stage 2

The driver steering wheel air bag high and/or low circuit is open for 120 milliseconds.

B0012 0D Stage 1 or B0013 0D Stage 2

The driver steering wheel air bag deployment loop resistance is greater than 5.1 ohms for 120 milliseconds.

B0012 0E Stage 1 or B0013 0E Stage 2

The driver steering wheel air bag deployment loop resistance is less than 1.3 ohms for 120 milliseconds.

Action Taken When the DTC Sets

* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.

* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.

Conditions for Clearing the DTC

* The condition for setting the DTC no longer exists.

* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.

Diagnostic Aids

* When a harness connector is disconnected, the high control and low control circuits are shorted together by the integral shorting bar. This

should be taken into account when testing for faults on these circuits.

* This DTC usually indicates a poor connection or a wiring malfunction between the SDM and the deployment loop.

Reference Information

Schematic Reference

SIR Schematics (See: Diagrams/Electrical Diagrams/Air Bag Systems)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Monday, December 16, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 919

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 919

Diagnostic Fault Information

Circuit/System Description

The electronic brake control module (EBCM) uses input from the brake master cylinder piston position sensor and the brake switch to determine

when the brake pedal is being applied and with how much force. These inputs are used to determine the driver's braking intent which is used to the

control amount of pressure applied to the wheels.

Conditions for Running the DTC

* Ignition ON.

* Ignition voltage is greater than 10 volts.

Conditions for Setting the DTC

C0277 03, C129A, or C129D

The EBCM detects voltage below threshold on signal circuit.

C0277 07, C129B, or C129E

The EBCM detects voltage above threshold on signal circuit.

C0277 5A, C12B1, C12F8, or C120C

This EBCM detects the master cylinder pressure is high when brake master cylinder piston position sensor is reading low travel.

Action Taken When the DTC Sets

* The EBCM disables the antilock brake system (ABS), traction control and the vehicle stability enhancement system for the duration of the

ignition cycle.

* A driver information center message and/or a warning indicator may be displayed.

Conditions for Clearing the DTC

* The condition for the DTC is no longer present.

* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.

Reference Information

Schematic Reference

Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS

Description and Operation)

Electrical Information Reference

Wednesday, December 11, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1424

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1424



Diagnostic Fault Information



Circuit/System Description



The transmission control module (TCM) within the control solenoid valve assembly continuously monitors the system voltage on the ignition



voltage circuit. Lower than normal voltage may be inadequate to operate the transmission control solenoids properly. Improper solenoid operation



may cause erratic transmission operation, which may result in internal damage. These DTCs detect high or low TCM voltage for an extended



period.



Conditions for Running the DTC



P0562



* Ignition voltage was 6.0 volts or greater and has not dropped below 2.0 volts.



* Engine speed is 1,200 RPM or greater.



P0563



Ignition voltage was 6.0 volts or greater and has not dropped below 2.0 volts.



P2534



* The engine is running.



* Ignition voltage was 6.0 volts or greater and has not dropped below 2.0 volts.



Conditions for Setting the DTC



P0562



The TCM detects system voltage is 11 volts or less for 4 seconds.



P0563



The TCM detects system voltage is 18 volts or greater for 10 seconds.



P2534



The TCM detects ignition voltage between 2.0 volts and 6.0 volts for 7 seconds or greater with the engine running.



Action Taken When the DTC Sets



P0562 and P0563



DTCs P0562 and P0563 are Type C DTCs.



P2534



* DTC P2534 is a Type A DTC.



* The TCM turns OFF all high side drivers.



* The TCM turns OFF all solenoids.



* The TCM commands maximum line pressure.



* The TCM freezes transmission adaptive functions.



* The TCM commands the torque converter clutch (TCC) OFF.



* The TCM allows the transmission to operate in reverse and fifth range.



* The TCM inhibits Tap Up/Down function.



* The TCM inhibits manual shifting of forward gears.



Conditions for Clearing the DTC



* DTCs P0562 and P0563 are Type C DTCs.



* DTC P2534 is a Type A DTC.



Diagnostic Aids



* Observe the driver information center (DIC) messaging that would indicate the electrical system requires service.



* Running the engine with a battery charger attached may cause DTC P0563 to set.



* Inspect for the following conditions:

Monday, December 9, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1160

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1160



Diagnostic Fault Information



Typical Scan Tool Data



Circuit/System Description



The throttle body assembly contains 2 throttle position sensors. The throttle position sensors are mounted to the throttle body assembly and are not



serviceable. The throttle position sensors provide a signal voltage that changes relative to throttle blade angle. The engine control module (ECM)



supplies the throttle position sensors with a common 5 V reference circuit , a common low reference circuit, and two independent signal circuits.



The throttle position sensors have opposite functionality. Throttle position sensor 1 signal voltage decreases from greater than 4 V at idle to less



than 1 V at wide open throttle (WOT). Throttle position sensor 2 signal voltage increases from less than 1 V at idle to greater than 4 V at WOT.



Conditions for Running the DTC



P0121



* The engine speed is greater than 480 RPM.



* The vehicle speed is 0 km/h (0 mph).



* The engine coolant temperature is greater than 5掳C (41掳F).



* The ignition voltage is greater than 8 V.



* The intake air temperature is greater than 5掳C (41掳F).



* DTC P0121 runs continuously when the above conditions are met.



P0122, P0123, P0222, and P0223



* The vehicle speed is 0 km/h (0 mph).



* The engine speed is greater than 250 RPM.



* The engine coolant temperature is greater than 5掳C (41掳F).



* The intake air temperature is greater than 5掳C (41掳F).



* The ignition voltage is greater than 8 V.



* The ignition is ON, with the engine OFF, or the engine is operating.



* DTC P0122 runs continuously when the above conditions are met.



P0221



* The engine speed is greater than 480 RPM.



* The vehicle speed is 0 km/h (0 mph).



* The engine coolant temperature is greater than 5掳C (41掳F).



* The ignition voltage is greater than 8 V.



* The intake air temperature is greater than 5掳C (41掳F).



* DTC P0221 runs continuously when the above conditions are met.



Conditions for Setting the DTC



P0121



The throttle position sensor 1 disagrees greater than 9 % from throttle position sensor 2, or throttle position sensor 1 disagrees greater than 9 %



from the predicted value for greater than 1 s or a cumulative of 4 s.

Wednesday, December 4, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 650

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 650

Diagnostic Fault Information

Circuit/System Description

The body control module (BCM) controls the horn relay by grounding the control circuit of the horn relay coil energizing the relay. When the horn

relay is energized, the horn relay contacts close applying voltage through the horn fuse and the horn control circuit to the horns.

Conditions for Running the DTC

When the output is actively being requested by the BCM.

Conditions for Setting the DTC

The BCM detects a short to ground, open or short to battery in the horn relay control circuit for approximately 125 milliseconds.

Action Taken When the DTC Sets

The BCM disables the output to the horn relay until the next ignition cycle.

Conditions for Clearing the DTC

* The DTC clears when the fault is no longer detected.

* The current DTC will become history when the request for the output is removed.

* The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.

Reference Information

Schematic Reference

Horn Schematics (See: Lighting and Horns/Horn/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Horns System Description and Operation (See: Lighting and Horns/Horn/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Command the horn ON and OFF with the scan tool. The horn should turn ON and OFF when changing between the commanded states.

Circuit/System Testing

1. Ignition OFF, disconnect the X4 harness connector at the underhood fuse block.

2. Connect a test lamp between the control circuit terminal G1 and B+.

3. Press and release the horn switch. The test lamp should turn ON and OFF when changing between the commanded states.

Thursday, November 28, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 540

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 540

Diagnostic Fault Information

Circuit/System Description

The front seat heating elements are controlled by a common high current relay internal to the heated seat control module (HSM) and on the low side

by individual element control circuits. The HSM connects the seat heater element supply voltage circuits to a common reference point. This

reference point is biased to approximately 2.5 V. Before the HSM will allow heated seat operation, it checks to see if the heating element supply

voltage circuits and control circuits are shorted to ground or battery voltage. Once the HSM verifies that it is not closing into a shorted heating

element, it allows heated seat operation. After which it continues to monitor for a shorted circuit.

Conditions for Running the DTC

The HSM must be powered.

Conditions for Setting the DTC

B2345 00

After a heated seat is activated, the HSM detects a shorted circuit on the seat heating element supply voltage circuit or control circuit.

B2345 13

Any of the temperature sensor inputs remains below 1.45 V for more than 1 second.

B2345 42

The current sensing calibration is not programmed.

B2345 4B

The current sensing calibration is out of range.

Monday, November 25, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 458

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 458

Diagnostic Fault Information

Circuit/System Description

The retained accessory power (RAP) system allows specific vehicle functions to operate after the ignition is turned OFF for a predetermined time.

The RAP relay is internal to the BCM. Relay RAP is controlled by the BCM using inputs from the door ajar switches to determine control of the

relay when the ignition is turned OFF. Radio RAP is controlled by a serial data message from the BCM using inputs from the driver door open

switch. Refer to Retained Accessory Power Description and Operation (See: Power and Ground Distribution/Description and Operation/Retained

Accessory Power Description and Operation) for more detail on RAP operation.

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The DTC can only set when the output is actively being requested by the module.

Conditions for Setting the DTC

The DTC will set only when the module requests the output and there is a short to ground detected in the RAP supply voltage circuit.

Action Taken When the DTC Sets

The BCM output driver will be shut down and not supply voltage to the circuit.

Conditions for Clearing the DTC

* The current DTC will clear when the module request for the output is removed or the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

Diagnostic Aids

* The RAP/Spare relay is permanently soldered to the left I/P junction block and is non-serviceable.

* The RAP mode for the radio and door modules is a separate function and will still operate properly.

Reference Information

Schematic Reference

Power Moding Schematics (See: Diagrams/Electrical Diagrams/Starting and Charging/Power and Ground Distribution/System Diagram/Power

Moding Schematics)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Retained Accessory Power Description and Operation (See: Power and Ground Distribution/Description and Operation/Retained Accessory Power

Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition ON, verify DTC B1475 is set as current.

Tuesday, November 19, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 980

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 980

Diagnostic Fault Information

Circuit/System Description

The electronic suspension control (ESC) module supplies a 5 volt reference signal to each suspension position sensor. The suspension position

sensors supply an voltage signal of 0.35-4.75 volts to the ESC module which represents the position between the body and the wheel. The sensors

are also grounded through the ESC module.

Conditions for Running the DTC

* Battery voltage is between 9-16 volts

* Ignition is ON

Conditions for Setting the DTC

* The DTC is set when the ESC module measures a position sensor signal voltage below 0.35 volt or above 4.75 volts for more than 1 second

while the vehicle is operated under normal driving conditions.

* The fault is detected during 3 consecutive ignition cycles, or during the same ignition cycle after clearing the DTC with a scan tool.

Action Taken When the DTC Sets

* The ESC will enter the speed dependent damping mode.

* Both left and right normal force outputs will be set to the default output states.

* The ESC sends a message to the instrument panel cluster (IPC) to display SERVICE SUSPENSION SYSTEM message.

Conditions for Clearing the DTC

A history DTC will clear after 50 consecutive ignition cycles if the condition for the malfunction is no longer present.

Reference Information

Schematic Reference

Electronic Suspension Control Schematics (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Diagrams/Electrical Diagrams/Electronic Suspension Control)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Electronic Suspension Control Description and Operation (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Description and Operation/Electronic Suspension Control Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

Monday, November 18, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 95

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 95

Diagnostic Fault Information

Circuit/System Description

If a malfunction is detected, a DTC will be stored in non-volatile memory. During a frontal crash of sufficient force the inflatable restraint sensing

and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the driver steering wheel air bag. The

SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage.

There are 2 shorting bars used within each connector which will short together both driver steering wheel air bag stage 1 high circuit and driver

steering wheel air bag stage 1 low circuit and both driver steering wheel air bag stage 2 high circuit and driver steering wheel air bag stage 2 low

circuit when the connector is disconnected. This will help to prevent unwanted deployment of the air bag during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0012 01 Stage 1 or B0013 01 Stage 2

The driver steering wheel air bag high and/or low circuit is shorted to voltage for 120 milliseconds.

B0012 02 Stage 1 or B0013 02 Stage 2

The driver steering wheel air bag high and/or low circuit is shorted to ground for 120 milliseconds.

B0012 04 Stage 1 or B0013 04 Stage 2

The driver steering wheel air bag high and/or low circuit is open for 120 milliseconds.

B0012 0D Stage 1 or B0013 0D Stage 2

The driver steering wheel air bag deployment loop resistance is greater than 5.1 ohms for 120 milliseconds.

B0012 0E Stage 1 or B0013 0E Stage 2

The driver steering wheel air bag deployment loop resistance is less than 1.3 ohms for 120 milliseconds.

Action Taken When the DTC Sets

* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.

* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.

Conditions for Clearing the DTC

* The condition for setting the DTC no longer exists.

* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.

Diagnostic Aids

* When a harness connector is disconnected, the high control and low control circuits are shorted together by the integral shorting bar. This

should be taken into account when testing for faults on these circuits.

* This DTC usually indicates a poor connection or a wiring malfunction between the SDM and the deployment loop.

Reference Information

Schematic Reference

SIR Schematics (See: Diagrams/Electrical Diagrams/Air Bag Systems)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)