2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 920
Note: When test probing harness terminals, it is imperative to use the proper test probe from the most current version of the J 35616 - Kit.
Use of an improper test probe may deform the terminal, resulting in intermittent open conditions.
1. Key OFF. Disconnect the X1 connector from the transfer case two/four wheel drive actuator position sensor also known as the rotational
position sensor (RPS).
2. Key ON, engine OFF.
3. Using the GY probe J 35616-2A, test for 4.75-5.25 V between the 5-volt reference circuit, RPS X1 pin B and a good ground (the ground
terminal of the EL-49742 - harness, black terminal).
瀚慖f the voltage is less than the specified range, test the affected circuit for an open/high resistance or short to ground. If all circuits and
connections test normal, test the TCCM for proper operation.
瀚慖f the voltage is greater than the specified range, test the affected circuit for a short to voltage. If all circuits and connections test normal,
test the TCCM for proper operation.
4. Using the GY probe J 35616-2A, test for 4.75-5.25 V between the 5-volt reference circuit, RPS X1 pin B and the low reference circuit, RPS
X1 pin A.
瀚慖f the voltage is less than the specified range, test the low reference circuit for an open/high resistance. If all circuits and connections test
normal, test the TCCM for proper operation.
瀚慖f the voltage is greater than the specified range, test the low reference circuit for a short to voltage. If all circuits and connections test
normal, test the TCCM for proper operation.
5. Using the GY probe J 35616-2A, test for 4.5-5.0 V between the rotary position sensor signal circuit, RPS X1 pin C and a good ground.
瀚慖f the voltage is less than the specified range, test the rotary position sensor signal circuit for an open/high resistance or short to ground. If
all circuits and connections test normal, test the TCCM for proper operation.
瀚慖f the voltage is greater than the specified range, test the rotary position sensor. signal circuit for a short to voltage. If all circuits and
connections test normal, test the TCCM for proper operation.
6. Using the GY probe J 35616-2A, test for greater than 500 ohm between the low reference circuit, RPS X1 pin A and all other pins of the RPS
X1.
瀚慖f the resistance is less than the specified range, test the affected circuits for a shorted together condition. If all circuits and connections
test normal, test the TCCM for proper operation.
7. Using the GY probe J 35616-2A, test for greater than 500 ohm between the 5-volt reference circuit, RPS X1 pin B and all other pins of the
RPS X1.
瀚慖f the resistance is less than the specified range, test the affected circuits for a shorted together condition. If all circuits and connections
test normal, test the TCCM for proper operation.
8. Key OFF. Disconnect TCCM connector X2.
9. Using the GY probe J 35616-2A, test for greater than 10 ohm between the low reference circuit, TCSCS X2 pin 9 and all other pins of the
TCCM X2.
瀚慖f the resistance is less than the specified range, test the affected circuits for a shorted together condition. If all circuits and connections
test normal, test the TCCM for proper operation.
10. Using the GY probe J 35616-2A, test for greater than 10 ohm between the rotational position sensor circuit, TCSCS X2 pin 11 and all other
pins of the TCCM X2.
瀚慖f the resistance is less than the specified range, test the affected circuits for a shorted together condition. If all circuits and connections
test normal, test the TCCM for proper operation.
11. Test the RPS for proper operation.
Transfer Case Two/Four Wheel Drive Actuator Position Sensor/Rotational Position Sensor (RPS)
1. Key OFF. Disconnect the X1 connector at the RPS.
2. Remove the RPS from the transfer case.
3. Connect the RPS.
4. While monitoring the Rotational Position Sensor parameter in the Data Display section of the scan tool, rotate the center locating tab of the
RPS. The Rotational Position Sensor parameter reading should sweep between -146 and +204 degrees.
瀚慖f the RPS does not function as explained, replace the RPS.
Transfer Case Shift Control Module (TCCM)
1. Key OFF. Disconnect the X1 connector.
Diagnostic Repair parts ,Wiring Diagrams. DTC. TSB,Car, Truck, SUV & Van Acura Chrysler Infiniti Maserati Rolls-Royce Alfa Romeo Dodge Jaguar Mazda Scion Aston Martin Ferrari Jeep McLaren Smart Audi Fiat Karma Mercedes-Benz Spyker BMW Ford Kia Mini Subaru Bentley Freightliner Lamborghini Mitsubishi Tesla Bugatti GMC Land Rover Mobility Ventures Toyota Buick Genesis Lexus Nissan Volkswagen Cadillac Honda Lincoln Porsche Volvo Chevrolet Hyundai Lotus Ram
Showing posts with label Note: When test probing harness terminals. Show all posts
Showing posts with label Note: When test probing harness terminals. Show all posts
Monday, November 18, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 920
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 906
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 906
Note: When test probing harness terminals, it is imperative to use the proper test probe from the most current version of the J 35616 - Kit.
Use of an improper test probe may deform the terminal, resulting in intermittent open conditions.
1. Verify that the TRANS IGN1 fuse, underhood fuse block, is not open.
瀚慖f the TRANS IGN1 fuse is open, test the Ignition 1 voltage circuit, front drive axle actuator harness X1 pin C, for a short to ground.
2. Wheels blocked. Parking brake engaged. Transmission in Neutral.
3. Ignition ON, engine OFF. Install a scan tool.
4. Disconnect the X1 harness connector at the front drive axle actuator (FDAA).
5. Using the GY probe J 35616-2A, test for B+ (+0.0/-1.0 V) between the Ignition 1 voltage circuit, FDAA X1 harness pin C, and a good
ground.
瀚慖f the voltage is less than the specified value, test the affected circuit for an open/high resistance or short to ground. If all circuits and
connections test normal, test the TCCM for proper operation.
6. Using the GY probe J 35616-2A, test for B+ (+0.0/-1.0 V) between the Ignition 1 voltage circuit, FDAA X1 harness pin C, and the ground
circuit, FDAA X1 harness pin E.
瀚慖f the voltage is less than the specified value, test the ground circuit for an open/high resistance or short to voltage. If all circuits and
connections test normal, test the TCCM for proper operation.
7. Using the GY probes J 35616-2A, test for B+ (+0.0/-1.0 V) between the Ignition 1 voltage circuit, FDAA X1 harness pin C and the axle
switch signal circuit, FDAA X1 harness pin A.
瀚慖f the voltage is less than the specified value, test the axle switch signal circuit for an open/high resistance, short to ground or short to
voltage. If all circuits and connections test normal, test the TCCM for proper operation.
8. Using the GY probes J 35616-2A, measure the voltage between the front axle actuator control circuit, FDAA X1 harness pin B and a good
ground, while commanding the front axle actuator ON and OFF using the Front Axle Actuator function of the Special Functions feature of
the scan tool. When commanded to ON the voltage should read 0.0 V. When commanded to OFF the voltage should read 3.5-6.0 V.
瀚慖f the measured voltage is less than 3.5 V when commanded OFF, test the front axle actuator control circuit for an open/high resistance or
short to ground. If all circuits and connections test normal, test the TCCM for proper operation.
瀚慖f the measured voltage is greater than 6.0 V when commanded ON, test the front axle actuator control circuit for a short to voltage. If all
circuits and connections test normal, test the TCCM for proper operation.
9. Go to Front Drive Axle Actuator (FDAA) in Component Testing.
Component Testing
Front Drive Axle Actuator (FDAA)
1. Key OFF. Disconnect the X1 connector at the FDAA.
2. Remove the FDAA.
3. Connect the FDAA X1 connector. Position the FDAA so that it is visible from the side of the vehicle.
4. Using the Engage Front Axle function of the Special Function feature of the scan tool, command the front axle ON and OFF. When
commanded ON the plunger on the FDAA should extend. When commanded OFF the plunger should retract.
瀚慖f the FDAA does not perform as described, replace the FDAA.
5. Refer to Front Axle Will Not Engage (See: Transmission and Drivetrain/Transfer Case/Testing and Inspection/Symptom Related Diagnostic
Procedures/MP 3010-NP0/Front Axle Will Not Engage) or Front Axle Will Not Disengage (See: Transmission and Drivetrain/Transfer
Case/Testing and Inspection/Symptom Related Diagnostic Procedures/MP 3010-NP0/Front Axle Will Not Disengage).
Transfer Case Shift Control Module (TCCM)
1. Key OFF. Disconnect the X1 connector at the front drive axle actuator (FDAA).
2. Key ON, engine OFF. Install a scan tool.
Note: When test probing harness terminals, it is imperative to use the proper test probe from the most current version of the J 35616 - Kit.
Use of an improper test probe may deform the terminal, resulting in intermittent open conditions.
3. Using the GY probe J 35616-2A, connect a test light between the Ignition 1 voltage circuit, FDAA X1 harness pin C and the front axle
actuator control circuit, FDAA X1 harness pin B.
4. Using the Engage Front Axle function of the Special Function feature of the scan tool, command the front axle ON and OFF. When
commanded ON the test light should illuminate. When commanded OFF the test light should turn OFF.
瀚慖f the TCCM does not perform as described, replace the TCCM.
5. Go to Circuit/System Verification.
Note: When test probing harness terminals, it is imperative to use the proper test probe from the most current version of the J 35616 - Kit.
Use of an improper test probe may deform the terminal, resulting in intermittent open conditions.
1. Verify that the TRANS IGN1 fuse, underhood fuse block, is not open.
瀚慖f the TRANS IGN1 fuse is open, test the Ignition 1 voltage circuit, front drive axle actuator harness X1 pin C, for a short to ground.
2. Wheels blocked. Parking brake engaged. Transmission in Neutral.
3. Ignition ON, engine OFF. Install a scan tool.
4. Disconnect the X1 harness connector at the front drive axle actuator (FDAA).
5. Using the GY probe J 35616-2A, test for B+ (+0.0/-1.0 V) between the Ignition 1 voltage circuit, FDAA X1 harness pin C, and a good
ground.
瀚慖f the voltage is less than the specified value, test the affected circuit for an open/high resistance or short to ground. If all circuits and
connections test normal, test the TCCM for proper operation.
6. Using the GY probe J 35616-2A, test for B+ (+0.0/-1.0 V) between the Ignition 1 voltage circuit, FDAA X1 harness pin C, and the ground
circuit, FDAA X1 harness pin E.
瀚慖f the voltage is less than the specified value, test the ground circuit for an open/high resistance or short to voltage. If all circuits and
connections test normal, test the TCCM for proper operation.
7. Using the GY probes J 35616-2A, test for B+ (+0.0/-1.0 V) between the Ignition 1 voltage circuit, FDAA X1 harness pin C and the axle
switch signal circuit, FDAA X1 harness pin A.
瀚慖f the voltage is less than the specified value, test the axle switch signal circuit for an open/high resistance, short to ground or short to
voltage. If all circuits and connections test normal, test the TCCM for proper operation.
8. Using the GY probes J 35616-2A, measure the voltage between the front axle actuator control circuit, FDAA X1 harness pin B and a good
ground, while commanding the front axle actuator ON and OFF using the Front Axle Actuator function of the Special Functions feature of
the scan tool. When commanded to ON the voltage should read 0.0 V. When commanded to OFF the voltage should read 3.5-6.0 V.
瀚慖f the measured voltage is less than 3.5 V when commanded OFF, test the front axle actuator control circuit for an open/high resistance or
short to ground. If all circuits and connections test normal, test the TCCM for proper operation.
瀚慖f the measured voltage is greater than 6.0 V when commanded ON, test the front axle actuator control circuit for a short to voltage. If all
circuits and connections test normal, test the TCCM for proper operation.
9. Go to Front Drive Axle Actuator (FDAA) in Component Testing.
Component Testing
Front Drive Axle Actuator (FDAA)
1. Key OFF. Disconnect the X1 connector at the FDAA.
2. Remove the FDAA.
3. Connect the FDAA X1 connector. Position the FDAA so that it is visible from the side of the vehicle.
4. Using the Engage Front Axle function of the Special Function feature of the scan tool, command the front axle ON and OFF. When
commanded ON the plunger on the FDAA should extend. When commanded OFF the plunger should retract.
瀚慖f the FDAA does not perform as described, replace the FDAA.
5. Refer to Front Axle Will Not Engage (See: Transmission and Drivetrain/Transfer Case/Testing and Inspection/Symptom Related Diagnostic
Procedures/MP 3010-NP0/Front Axle Will Not Engage) or Front Axle Will Not Disengage (See: Transmission and Drivetrain/Transfer
Case/Testing and Inspection/Symptom Related Diagnostic Procedures/MP 3010-NP0/Front Axle Will Not Disengage).
Transfer Case Shift Control Module (TCCM)
1. Key OFF. Disconnect the X1 connector at the front drive axle actuator (FDAA).
2. Key ON, engine OFF. Install a scan tool.
Note: When test probing harness terminals, it is imperative to use the proper test probe from the most current version of the J 35616 - Kit.
Use of an improper test probe may deform the terminal, resulting in intermittent open conditions.
3. Using the GY probe J 35616-2A, connect a test light between the Ignition 1 voltage circuit, FDAA X1 harness pin C and the front axle
actuator control circuit, FDAA X1 harness pin B.
4. Using the Engage Front Axle function of the Special Function feature of the scan tool, command the front axle ON and OFF. When
commanded ON the test light should illuminate. When commanded OFF the test light should turn OFF.
瀚慖f the TCCM does not perform as described, replace the TCCM.
5. Go to Circuit/System Verification.
Subscribe to:
Posts (Atom)