Showing posts with label P0348. Show all posts
Showing posts with label P0348. Show all posts

Tuesday, February 18, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1301

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1301



2. Engine idling, observe the DTC information with a scan tool. DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368,



P0391, P0392, or P0393 should not set.



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, remove the fuse that supplies B+ to terminal 56-X2 of the ECM.



2. Disconnect the harness connector at the appropriate camshaft position sensor.



Note: The control module or the sensor may be damaged if the circuit is shorted to B+ voltage.



3. Test for 5 ohm or less between the low reference circuit terminal 1 and ground.



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the



circuit/connections test normal, replace the ECM.



4. Install the fuse that supplies B+ to terminal 56-X2 of the ECM.



5. Ignition ON, test for greater than 4.8 V between the 5-volt reference circuit terminal 3 and ground.



瀚慖f less than the specified value, test the 5-volt reference circuit for an open/high resistance. If the circuits/connections test normal, replace



the ECM.



6. Test for 4.8-5.2 V between the signal circuit terminal 2 and ground.



瀚慖f the voltage is greater than specified range, test for a short to voltage in the signal circuit. If circuit/connections test normal, replace the



ECM.



瀚慖f the voltage is less than the specified range, test for a short to ground or an open/high resistance in the signal circuit. If



circuit/connections test normal, replace the ECM.



7. If all circuits/connections test normal, replace the camshaft position sensor.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)



* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)



* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust)



* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control



Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and



programming



P0351



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (LAU)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit

Thursday, December 26, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1332

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1332



DTCs P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, and P0393 are Type B DTCs.



Conditions for Clearing the DTC



DTCs P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, and P0393 are Type B DTCs.



Diagnostic Aids



The following conditions can also set the DTC:



* Physical damage to the camshaft position sensor or the reluctor wheel



* Excessive play or looseness of the camshaft position sensor or the reluctor wheel



* Improper installation of the camshaft position sensor or the reluctor wheel



* Foreign material passing between the camshaft position sensor and the reluctor wheel



* Excessive air gap between the camshaft position sensor and the reluctor wheel



* The cylinder 1 intake camshaft position sensor is used for injector and ignition system synchronization. A stalling condition will occur if the



CMP sensor signal is intermittent and a DTC will not set. Inspect all cylinder 1 intake camshaft position sensor circuits for poor connections.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft



Actuator System)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ignition ON, observe the DTC information with a scan tool. DTC P0651, P0652 or P0653 should not be set.



瀚慖f a DTC is set, refer to DTC P0641-P0643, P0651-P0653, or P0697-P0699 (ECM, LAU) ( See: P Code Charts/P0641/ECM).



2. Engine idling, observe the DTC information with a scan tool. DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368,



P0391, P0392, or P0393 should not set.



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, remove the fuse that supplies B+ to terminal 56-X2 of the ECM.



2. Disconnect the harness connector at the appropriate camshaft position sensor.



Note: The control module or the sensor may be damaged if the circuit is shorted to B+ voltage.



3. Test for 5 ohm or less between the low reference circuit terminal 1 and ground.

Sunday, December 1, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1288

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1288



DTCs P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, and P0393 are Type B DTCs.



Conditions for Clearing the DTC



DTCs P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, and P0393 are Type B DTCs.



Diagnostic Aids



The following conditions can also set the DTC:



* Physical damage to the camshaft position sensor or the reluctor wheel



* Excessive play or looseness of the camshaft position sensor or the reluctor wheel



* Improper installation of the camshaft position sensor or the reluctor wheel



* Foreign material passing between the camshaft position sensor and the reluctor wheel



* Excessive air gap between the camshaft position sensor and the reluctor wheel



* The cylinder 1 intake camshaft position sensor is used for injector and ignition system synchronization. A stalling condition will occur if the



CMP sensor signal is intermittent and a DTC will not set. Inspect all cylinder 1 intake camshaft position sensor circuits for poor connections.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft



Actuator System)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ignition ON, observe the DTC information with a scan tool. DTC P0651, P0652 or P0653 should not be set.



瀚慖f a DTC is set, refer to DTC P0641-P0643, P0651-P0653, or P0697-P0699 (ECM, LAU) ( See: P Code Charts/P0641/ECM).



2. Engine idling, observe the DTC information with a scan tool. DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368,



P0391, P0392, or P0393 should not set.



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, remove the fuse that supplies B+ to terminal 56-X2 of the ECM.



2. Disconnect the harness connector at the appropriate camshaft position sensor.



Note: The control module or the sensor may be damaged if the circuit is shorted to B+ voltage.



3. Test for 5 ohm or less between the low reference circuit terminal 1 and ground.