Diagnostic Repair parts ,Wiring Diagrams. DTC. TSB,Car, Truck, SUV & Van Acura Chrysler Infiniti Maserati Rolls-Royce Alfa Romeo Dodge Jaguar Mazda Scion Aston Martin Ferrari Jeep McLaren Smart Audi Fiat Karma Mercedes-Benz Spyker BMW Ford Kia Mini Subaru Bentley Freightliner Lamborghini Mitsubishi Tesla Bugatti GMC Land Rover Mobility Ventures Toyota Buick Genesis Lexus Nissan Volkswagen Cadillac Honda Lincoln Porsche Volvo Chevrolet Hyundai Lotus Ram
Sunday, November 29, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2445
P1751
DTC P1751
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P1751
- Shift Valve 1 Performance
Circuit/System Description
The shift solenoid (SS) 1 is part of the control solenoid valve assembly, which has no serviceable parts. SS 1 provides fluid pressure to control the
operation of the clutch select valve 2, which is located in the control valve lower body assembly. SS 1, in conjunction with clutch select valve 2,
controls fluid to the R1 and 4-5-6 clutches. A diagnostic test is performed by the transmission control module (TCM) to determine the state of the
clutch select valve 2. During this diagnostic test, the TCM commands the SS 1 ON, supplying pressure to move the clutch select valve 2 toward its
spring. At the same time, line pressure is elevated slightly to assist the spring side pressure. If the spring is broken, or the clutch select valve 2
cannot move due to another mechanical condition the DTC will set.
Conditions for Running the DTC
* DTCs P0716, P0717, P0722, P0723, P0741, P0742, P1751, P2762, P2763, or P2764 are not set.
* The engine speed is 500 RPM or greater for 5 seconds or greater.
* The transmission fluid temperature (TFT) is 20-130掳C (68-266掳F).
* The calculated throttle position is between 8-90 percent.
* The engine torque is greater than 50 Nm (36 lb ft).
* No upshift or downshift in process.
* The attained gear slip is 70 RPM or greater.
Conditions for Setting the DTC
The TCM detects attained gear slip is 75 RPM or greater for 1 second.
Action Taken When the DTC Sets
DTC P1751 is a Type B DTC.
Conditions for Clearing the DTC
* DTC P1751 is a Type B DTC.
* The TCM freezes transmission adaptive functions.
Diagnostic Aids
Before performing a road test, configure and setup the scan tool for snapshot mode. This will allow you to display, monitor, and verify multiple
transmission data parameters at one time, after the road test.
Reference Information
Connector End View Reference
* Component Connector End Views (See: Diagrams/Connector Views)
* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Friday, March 27, 2020
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1785
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1785
P1751
DTC P1751
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P1751
- Shift Valve 1 Performance
Circuit/System Description
The shift solenoid (SS) 1 is part of the control solenoid valve assembly, which has no serviceable components. SS 1 provides fluid pressure to
control the operation of the clutch select valve 2, which is located in the control valve lower body assembly. SS 1, in conjunction with clutch select
valve 2, controls the pressure path to the reverse and low clutch and 4-5-6 clutch. A diagnostic test is performed by the transmission control module
(TCM) to determine the state of the clutch select valve 2. During this diagnostic test, the TCM commands the SS 1 ON, supplying pressure to move
the clutch select valve 2 toward its spring. At the same time, line pressure is elevated slightly to assist the spring side pressure. If the spring is
broken, or the clutch select valve 2 cannot move due to another mechanical condition, the DTC will set.
Conditions for Running the DTC
* No DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207,
P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, P0741, P0742,
P1751, P2763, or P2764.
* Current gear is not 2nd.
* The engine speed is greater than 400 RPM for greater than 5 seconds.
* The ignition voltage is 8.6 volts or greater.
* The transmission fluid temperature (TFT) is 20-130掳C (68-266掳F).
* The calc. throttle position is 8 percent or greater.
* The engine torque is greater than 80 Nm (59 lb ft).
* The transmission input speed is greater than 1200 RPM.
* No upshift or downshift in process.
Conditions for Setting the DTC
The TCM detects attained gear slip is 100 RPM or greater for 1 second.
Action Taken When the DTC Sets
DTC P1751 is a Type B DTC.
Conditions for Clearing the DTC
DTC P1751 is a Type B DTC.
Diagnostic Aids
Before performing a road test, configure and setup the scan tool for snapshot mode. This will allow you to display, monitor, and verify multiple
transmission data parameters at one time, after the road test.
Reference Information
Description and Operation
Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/6T70/6T75 -
Automatic Transmission/Transmission General Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)