2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1694
瀚慖f the test lamp does not illuminate, or flash, test the control circuit for a short to voltage, or an open/high resistance. If the
circuit/connections test normal, replace the K20 ECM.
Note:
* Less than 10 ohm on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a circuit the driver will remain
ON and the scan tool will display greater than 0.00 amp.
* Performing this test may set additional DTCs.
5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal listed below and the ignition voltage circuit terminal D.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
6. Engine idling, observe the appropriate B52 HO2S Heater parameter. The scan tool should display 0.00 A.
瀚慖f greater than the specified value, test the control circuit and the ignition voltage circuit for high resistance.
7. If all circuits test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming
P0053
DTC P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141, P0155, or P0161
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0030
- HO2S Heater Control Circuit Bank 1 Sensor 1
DTC P0036
- HO2S Heater Control Circuit Bank 1 Sensor 2
DTC P0050
- HO2S Heater Control Circuit Bank 2 Sensor 1
DTC P0053
- HO2S Heater Resistance Bank 1 Sensor 1
DTC P0054
- HO2S Heater Resistance Bank 1 Sensor 2
