Showing posts with label 瀚慖f the test lamp does not illuminate. Show all posts
Showing posts with label 瀚慖f the test lamp does not illuminate. Show all posts

Monday, December 21, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2991

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2991

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

EBCM.

3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2156

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Saturday, December 19, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2934

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2934

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

EBCM.

3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2128

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Thursday, November 19, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2207

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2207

瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or a open/high resistance. If the circuit tests normal and

ignition circuit fuse is open, test all components connected to the ignition circuit and replace as necessary.

4. Verify that a test lamp illuminates between the relay B+ circuit terminal 30 and ground.

瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or a open/high resistance. If the circuit tests normal and B+

circuit fuse is open, replace the A/C clutch relay.

5. Disconnect the harness connector at the A/C clutch coil.

6. Test for less than 1 ohm between the ground circuit terminal 2 and ground.

瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.

7. Connect the harness connector at the A/C clutch coil.

8. Connect a 10-amp fused jumper wire between the B+ circuit terminal 30 and control circuit terminal 87. Verify the A/C clutch is activated.

瀚慖f the A/C clutch does not activate, test the control circuit for an open/high resistance. If the circuit tests normal, test or replace the A/C

clutch.

9. Connect a test lamp between the ignition circuit terminal 85 and the control circuit terminal 86.

10. Command the A/C relay output function ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the

commanded states.

瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.

瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage, or an open/high resistance. If the circuit tests normal, replace

the ECM.

11. If all circuits test normal, test or replace the A/C clutch relay.

Component Testing

1. Ignition OFF, disconnect the A/C COMP relay.

2. Test for 60-180 ohms between terminals 85 and 86.

瀚慖f the resistance is not within the specified range, replace the relay.

3. Test for infinite resistance between the following terminals:

* 30 and 86

* 30 and 87

* 30 and 85

* 85 and 87

瀚慖f not the specified value, replace the relay.

4. Install a 30-amp fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test

for less than 2 ohms between terminals 30 and 87.

瀚慖f greater than the specified range, replace the relay.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay

Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power

Distribution Relay/Service and Repair/Relay Replacement (Within an Electrical Center))

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

HVAC - Automatic

DTC P0645

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

Monday, November 9, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1967

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1967

瀚慖f the test lamp does not illuminate, test the low reference circuit terminal A for a short to voltage or an open/high resistance. If the circuit

tests normal, replace the K27 fuel pump control module.

6. If all circuits test normal, replace the fuel tank G12 fuel pump module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Tank Fuel Pump Module Replacement (2500 LWB - 43.5L (11.5 gal) Tank Rear) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (2500 LWB - 43.5L (11.5 Gal) Tank Rear))Fuel Tank

Fuel Pump Module Replacement (2500 LWB - 98.4L (26 gal) Tank Front) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (2500 LWB - 98.4L (26 Gal) Tank Front))Fuel Tank

Fuel Pump Module Replacement (1500 SWB - 98.4L (26 gal) Tank + E85) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (1500 SWB - 98.4L (26 Gal) Tank + E85))Fuel Tank

Fuel Pump Module Replacement (1500 Series) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and

Repair/Fuel Tank Fuel Pump Module Replacement (1500 Series))Fuel Tank Fuel Pump Module Replacement (1500 LWB - 117.3L (31 gal)

Tank + E85) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module

Replacement (1500 LWB - 117.3L (31 Gal) Tank + E85))

* Control Module References (See: Testing and Inspection/Programming and Relearning)for fuel pump control module replacement, setup,

and programming

P254F

DTC P254F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P254F

- Engine Hood Switch Circuit

Diagnostic Fault Information

Circuit/System Description

The engine control module (ECM) monitors the voltage input of the hood open switch signal circuit and the hood open closed switch signal circuit.

With the hood open, the hood ajar portion of the switch is closed, grounding the hood ajar switch signal circuit from the ECM, and the hood closed

portion of the switch is open. With the hood closed, the hood closed portion of the switch is closed, grounding the hood closed switch signal circuit

from the ECM, and the hood ajar portion of the switch is open. During proper operation, the two separate voltage signals at the ECM should never

be at the same voltage.

Conditions for Running the DTC

The ECM continuously monitors for this DTC

Conditions for Setting the DTC

Both the hood open switch signal circuit and the hood closed switch signal circuit are simultaneously in an active or inactive state.

Action Taken When the DTC Sets

Engine starting will be disabled.

Saturday, November 7, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1938

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1938

瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests

normal and the ignition voltage circuit fuse is open, test or replace the fuel injector.

3. Connect the J 34730-405 between the control circuit terminal B and the ignition voltage circuit terminal A.

4. Command the fuel injector ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded

states.

瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the engine control module

(ECM).

瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the ECM.

5. If all circuits test normal, test or replace the fuel injector.

Component Testing

Note: The engine coolant temperature (ECT) sensor must be between 10-32掳C (50-90掳F) for an accurate measurement.

Measure for 11-14 ohm between the terminals of the fuel injector.

If not within the specified range, replace the fuel injector.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injector Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Service and Repair/Removal and

Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P215B

DTC P215B

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P215B

- Vehicle Speed - Output Shaft Speed (OSS) Correlation

Diagnostic Fault Information

Typical Scan Tool Data

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1933

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1933

瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests

normal and the ignition voltage circuit fuse is open, test or replace the fuel injector.

3. Connect the J 34730-405 between the control circuit terminal B and the ignition voltage circuit terminal A.

4. Command the fuel injector ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded

states.

瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the engine control module

(ECM).

瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the ECM.

5. If all circuits test normal, test or replace the fuel injector.

Component Testing

Note: The engine coolant temperature (ECT) sensor must be between 10-32掳C (50-90掳F) for an accurate measurement.

Measure for 11-14 ohm between the terminals of the fuel injector.

If not within the specified range, replace the fuel injector.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injector Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Service and Repair/Removal and

Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0207

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207, or P0208

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Injector 1 Control Circuit

DTC P0202

- Injector 2 Control Circuit

DTC P0203

- Injector 3 Control Circuit

DTC P0204

- Injector 4 Control Circuit

DTC P0205

- Injector 5 Control Circuit

DTC P0206

- Injector 6 Control Circuit

DTC P0207

- Injector 7 Control Circuit

DTC P0208

- Injector 8 Control Circuit

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1928

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1928

瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests

normal and the ignition voltage circuit fuse is open, test or replace the fuel injector.

3. Connect the J 34730-405 between the control circuit terminal B and the ignition voltage circuit terminal A.

4. Command the fuel injector ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded

states.

瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the engine control module

(ECM).

瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the ECM.

5. If all circuits test normal, test or replace the fuel injector.

Component Testing

Note: The engine coolant temperature (ECT) sensor must be between 10-32掳C (50-90掳F) for an accurate measurement.

Measure for 11-14 ohm between the terminals of the fuel injector.

If not within the specified range, replace the fuel injector.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injector Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Service and Repair/Removal and

Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0205

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207, or P0208

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Injector 1 Control Circuit

DTC P0202

- Injector 2 Control Circuit

DTC P0203

- Injector 3 Control Circuit

DTC P0204

- Injector 4 Control Circuit

DTC P0205

- Injector 5 Control Circuit

DTC P0206

- Injector 6 Control Circuit

DTC P0207

- Injector 7 Control Circuit

DTC P0208

- Injector 8 Control Circuit

Monday, November 2, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1811

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1811

瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests

normal and the B52 HO2S heater circuit fuse is open, test all components connected to the fuse and replace as necessary.

3. Probe the appropriate control circuit terminal listed below with a test lamp connected to B+. Verify that the test lamp does not illuminate.

* B52 HO2S 1 terminal E

* B52 HO2S 2 terminal C

瀚慖f the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

4. Engine idling, the test lamp should illuminate, or flash.

瀚慖f the test lamp does not illuminate, or flash, test the control circuit for a short to voltage, or an open/high resistance. If the

circuit/connections test normal, replace the K20 ECM.

Note:

* Less than 10 ohm on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a circuit the driver will remain

ON and the scan tool will display greater than 0.00 amp.

* Performing this test may set additional DTCs.

5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal listed below and the ignition voltage circuit terminal D.

* B52 HO2S 1 terminal E

* B52 HO2S 2 terminal C

6. Engine idling, observe the appropriate B52 HO2S Heater parameter. The scan tool should display 0.00 A.

瀚慖f greater than the specified value, test the control circuit and the ignition voltage circuit for high resistance.

7. If all circuits test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P150C

DTC P150C

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P150C

- Transmission Control Module Engine Speed Request Signal Message Counter Incorrect

Thursday, October 29, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1711

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1711

瀚慖f the test lamp does not illuminate, or flash, test the control circuit for a short to voltage, or an open/high resistance. If the

circuit/connections test normal, replace the K20 ECM.

Note:

* Less than 10 ohm on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a circuit the driver will remain

ON and the scan tool will display greater than 0.00 amp.

* Performing this test may set additional DTCs.

5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal listed below and the ignition voltage circuit terminal D.

* B52 HO2S 1 terminal E

* B52 HO2S 2 terminal C

6. Engine idling, observe the appropriate B52 HO2S Heater parameter. The scan tool should display 0.00 A.

瀚慖f greater than the specified value, test the control circuit and the ignition voltage circuit for high resistance.

7. If all circuits test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P060B

DTC P0601-P0606, P060B, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0601

- Transmission Control Module (TCM) Read Only Memory (ROM)

DTC P0602

- Transmission Control Module (TCM) Not Programmed

DTC P0603

- Transmission Control Module (TCM) Long Term Memory Reset

DTC P0604

- Transmission Control Module (TCM) Random Access Memory (RAM)

DTC P0606

- Transmission Control Module (TCM) Internal Performance

Wednesday, October 28, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1694

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1694

瀚慖f the test lamp does not illuminate, or flash, test the control circuit for a short to voltage, or an open/high resistance. If the

circuit/connections test normal, replace the K20 ECM.

Note:

* Less than 10 ohm on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a circuit the driver will remain

ON and the scan tool will display greater than 0.00 amp.

* Performing this test may set additional DTCs.

5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal listed below and the ignition voltage circuit terminal D.

* B52 HO2S 1 terminal E

* B52 HO2S 2 terminal C

6. Engine idling, observe the appropriate B52 HO2S Heater parameter. The scan tool should display 0.00 A.

瀚慖f greater than the specified value, test the control circuit and the ignition voltage circuit for high resistance.

7. If all circuits test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0053

DTC P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141, P0155, or P0161

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0030

- HO2S Heater Control Circuit Bank 1 Sensor 1

DTC P0036

- HO2S Heater Control Circuit Bank 1 Sensor 2

DTC P0050

- HO2S Heater Control Circuit Bank 2 Sensor 1

DTC P0053

- HO2S Heater Resistance Bank 1 Sensor 1

DTC P0054

- HO2S Heater Resistance Bank 1 Sensor 2

Sunday, December 1, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1473

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1473



瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.



瀚慖f the circuit tests normal and the B+ circuit fuse is open, test the control circuit terminal 87 for a short to ground.



4. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.



瀚慖f the test lamp illuminates, test the control circuit for a short to voltage.



5. Parking brake applied and the transmission is in NEUTRAL or PARK. Momentarily install a 30 A fused jumper wire between the B+ circuit



terminal 30 and the control circuit terminal 87. Verify the starter is activated.



瀚慖f the starter does not activate, test the control circuit for an open/high resistance. If the circuit tests normal, test or replace the starter.



6. Ignition OFF, connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85.



7. Transmission in park or neutral, cycle the ignition between the OFF and CRANK position. The test lamp should turn ON and OFF when



changing between the selected states.



瀚慖f the test lamp is always ON, test the control circuit for short to voltage. If the circuit tests normal, replace the K20 ECM.



瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace



the K20 ECM.



8. If all circuits tests normal, replace the KR27 starter relay.



Component Testing



Relay Test



1. Ignition OFF, disconnect the starter relay.



2. Test for 60-180 Ohms between terminals 85 and 86.



瀚慖f not within the specified range, replace the relay.



3. Test for infinite resistance between the following terminals:



* 30 and 86



* 30 and 87



* 30 and 85



* 85 and 87



瀚慖f not the specified value, replace the relay.



4. Install a 20 A fused jumper wire between relay terminal 85 and 12 V. Install a jumper wire between relay terminal 86 and ground. Test for



less than 2 Ohms between terminals 30 and 87.



瀚慖f greater than specified range, replace the relay.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay



Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power



Distribution Relay/Service and Repair/Relay Replacement (Within an Electrical Center))



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P0616



DTC P0615, P0616, or P0617



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.

Wednesday, November 13, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 478

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 478

瀚慖f the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

Note: The ignition switch component test must be preformed before proceeding with this test to verify the integrity of the switch.

4. Perform the ignition switch component test. The test should pass.

瀚慖f the ignition switch fails, replace the ignition switch.

5. Ignition OFF, disconnect the X1 harness connector at the BCM, test for less than 1.0 volt between the following circuit terminals of the BCM

and ground.

* Ignition key resistor signal terminal 4

* Off/Run/Crank voltage terminal 2

* Accessory voltage terminal 21

* Ignition 1 voltage terminal 14

瀚慖f greater than specified, test the circuit for a short to voltage.

6. Test for less than 1.0 ohm of resistance between the BCM and the ignition switch on the following circuit terminals.

* Ignition key resistor signal, BCM terminal 4 and ignition switch terminal 6

* Off/Run/Crank voltage, BCM terminal 2 and ignition switch terminal 5

* Accessory voltage, BCM terminal 21 and ignition switch terminal 3

* Ignition 1 voltage, BCM terminal 14 and ignition switch terminal 2

瀚慖f greater than specified, repair the circuit for open/high resistance

7. Test for infinite resistance between the ignition key resistor signal circuit terminal 4 of the BCM and ground.

瀚慖f less than specified, repair the signal circuit for a short to ground.

8. If all circuits test normal, replace the BCM.

Component Testing

Ignition Switch

1. Ignition OFF, disconnect the harness connector at the ignition switch.

2. Using the Resistance Test table below, check the resistance between the terminals of the ignition switch listed in each switch position.

If any reading is not as specified, replace the ignition switch.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming

* Ignition and Start Switch Replacement (See: Powertrain Management/Ignition System/Sensors and Switches - Ignition System/Ignition

Switch/Service and Repair)

B1449

DTC B1449

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

Wednesday, November 6, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1259

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1259

瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the

B+ circuit fuse is open, test the control circuit terminal 4 for a short to ground. If the circuit tests normal, replace the battery vent fan

relay.

4. Verify that a test lamp illuminates between the B+ circuit terminal 2 and ground.

瀚慖f the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

5. Connect a 15 A fused jumper wire between the B+ circuit terminal 3 and the control circuit terminal 4. Verify the generator battery vent fan

is activated.

瀚慖f the cooling fan does not activate, test the control circuit for an open/high resistance. If the circuit tests normal, test or replace the

generator battery vent fan.

6. Connect a test lamp between the B+ circuit terminal 2 and the control circuit terminal 1.

7. Command the battery pack vent fan speed between 0 and 60 percent with a scan tool. The test lamp should turn ON and OFF after a 10

second delay.

瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the drive motor generator

battery control module.

瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the drive motor generator battery control module.

8. If all circuits test normal, test or replace the generator battery vent fan relay.

Component Testing

Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal

Protection Equipment (PPE) and proper procedures must be followed.

The High Voltage Disabling procedure will perform the following tasks:

* Identify how to disable high voltage.

* Identify how to test for the presence of high voltage.

* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures must

be followed.

Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:

* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.

* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.

- Visually and functionally inspect the gloves before use.

- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or

not.

Failure to follow the procedures exactly as written may result in serious injury or death.

Fan Relay Test

1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().

2. Ignition OFF, disconnect the drive motor generator battery vent fan relay.

3. Test for 85-110 ohm between terminals 1 and 2.

瀚慖f not within the specified range, replace the relay.

4. Test for infinite resistance between the following terminals:

* 1 and 3

* 1 and 4

* 2 and 3

* 2 and 4

* 3 and 4

瀚慖f not the specified value, replace the relay.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1485

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1485



瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.



2. Ignition OFF, disconnect the X2 harness connector at the G13 Generator.



3. Ignition ON, verify the scan tool Generator F-Terminal Signal parameter displays less than 5%.



瀚慖f greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the K20



Engine Control Module.



4. Install a 3 A fused jumper wire between B+ and the signal circuit terminal 2.



5. Verify the scan tool Generator F-Terminal Signal parameter displays greater than 95%.



瀚慖f less than the specified range, test the signal circuit terminal 2 for a short to ground or an open/high resistance. If the circuit tests



normal, replace the K20 Engine Control Module.



6. If the circuit tests normal replace the G13 Generator.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Generator Replacement (LF1) (See: Starting and Charging/Charging System/Alternator/Service and Repair)Generator Replacement (LAU)



(See: Starting and Charging/Charging System/Alternator/Service and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup and programming



P0627



DTC P0627-P0629



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0627



- Fuel Pump Enable Circuit



DTC P0628



- Fuel Pump Enable Circuit Low Voltage



DTC P0629



- Fuel Pump Enable Circuit High Voltage



Diagnostic Fault Information



Circuit/System Description



The engine control module (ECM) provides ignition voltage to the fuel pump flow control module whenever the engine is cranking or running. The



control module enables the fuel pump flow control module as long as the engine is cranking or running, and ignition system reference pulses are



received. While this enable voltage is being received, the fuel pump flow control module supplies a varying voltage to the in-tank fuel pump



module in order to maintain the desired fuel line pressure.



Conditions for Running the DTC



* The engine speed is greater than 0 RPM.



* The ignition voltage is between 11-18 V.



* The DTCs run continuously when the conditions above are met.



Conditions for Setting the DTC

Wednesday, October 30, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3106

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3106

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

EBCM.

3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2156

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.