2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2991
瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
EBCM.
3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.
瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
4. If all circuits test normal, replace the yaw rate sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/GMLAN Wiring Repairs)
* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and
Operation/ABS Description and Operation) for the ABS - Hybrid
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg
(8600 lb) GVW
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to
3900 kg (8600 lb) GVW
* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming
U2156
DTC U2105-U2199
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC U2142 00
- Lost Communication With Yaw Rate Sensor (YRS)
Circuit/System Description
Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be
exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an
availability indication of the transmitter module. Each message contains the identification number of the transmitter module.
The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the
ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus
serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain
Management/Computers and Control Systems/Information Bus/Description and Operation).
Conditions for Running the DTC
* The system voltage is between 9-16 volts.
* The vehicle power mode master requires serial data communication to occur.
Conditions for Setting the DTC
A supervised periodic message that includes the transmitter module availability has not been received.
Action Taken When the DTC Sets
* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.
* System OFF lamps will illuminate for these systems.
Diagnostic Repair parts ,Wiring Diagrams. DTC. TSB,Car, Truck, SUV & Van Acura Chrysler Infiniti Maserati Rolls-Royce Alfa Romeo Dodge Jaguar Mazda Scion Aston Martin Ferrari Jeep McLaren Smart Audi Fiat Karma Mercedes-Benz Spyker BMW Ford Kia Mini Subaru Bentley Freightliner Lamborghini Mitsubishi Tesla Bugatti GMC Land Rover Mobility Ventures Toyota Buick Genesis Lexus Nissan Volkswagen Cadillac Honda Lincoln Porsche Volvo Chevrolet Hyundai Lotus Ram
Showing posts with label replace the. Show all posts
Showing posts with label replace the. Show all posts
Monday, December 21, 2020
Saturday, December 19, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2934
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2934
瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
EBCM.
3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.
瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
4. If all circuits test normal, replace the yaw rate sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/GMLAN Wiring Repairs)
* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and
Operation/ABS Description and Operation) for the ABS - Hybrid
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg
(8600 lb) GVW
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to
3900 kg (8600 lb) GVW
* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming
U2128
DTC U2105-U2199
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC U2142 00
- Lost Communication With Yaw Rate Sensor (YRS)
Circuit/System Description
Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be
exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an
availability indication of the transmitter module. Each message contains the identification number of the transmitter module.
The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the
ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus
serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain
Management/Computers and Control Systems/Information Bus/Description and Operation).
Conditions for Running the DTC
* The system voltage is between 9-16 volts.
* The vehicle power mode master requires serial data communication to occur.
Conditions for Setting the DTC
A supervised periodic message that includes the transmitter module availability has not been received.
Action Taken When the DTC Sets
* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.
* System OFF lamps will illuminate for these systems.
瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
EBCM.
3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.
瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
4. If all circuits test normal, replace the yaw rate sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/GMLAN Wiring Repairs)
* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and
Operation/ABS Description and Operation) for the ABS - Hybrid
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg
(8600 lb) GVW
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to
3900 kg (8600 lb) GVW
* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming
U2128
DTC U2105-U2199
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC U2142 00
- Lost Communication With Yaw Rate Sensor (YRS)
Circuit/System Description
Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be
exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an
availability indication of the transmitter module. Each message contains the identification number of the transmitter module.
The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the
ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus
serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain
Management/Computers and Control Systems/Information Bus/Description and Operation).
Conditions for Running the DTC
* The system voltage is between 9-16 volts.
* The vehicle power mode master requires serial data communication to occur.
Conditions for Setting the DTC
A supervised periodic message that includes the transmitter module availability has not been received.
Action Taken When the DTC Sets
* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.
* System OFF lamps will illuminate for these systems.
Saturday, December 5, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2604
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2604
瀚慖f not the specified value, test the appropriate control circuit listed below for a short to voltage. If the circuit tests normal, replace the
ECM.
* Cylinder deactivation solenoid valve 1 terminal C
* Cylinder deactivation solenoid valve 2 terminal A
* Cylinder deactivation solenoid valve 3 terminal B
* Cylinder deactivation solenoid valve 4 terminal D
7. Install a 3 A fused jumper wire between the appropriate control circuit terminal listed below and the ignition circuit terminal E. Command the
appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve Control Circuit
High Voltage Test Status parameter displays Malfunction.
* Cylinder deactivation solenoid valve 1 terminal C
* Cylinder deactivation solenoid valve 2 terminal A
* Cylinder deactivation solenoid valve 3 terminal B
* Cylinder deactivation solenoid valve 4 terminal D
瀚慖f not the specified value, test the control circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
8. If all the circuits test normal, test or replace the valve lifter oil manifold assembly.
Component Testing
Static Test
1. Ignition OFF, disconnect the harness connector at the valve lifter oil manifold assembly.
2. Connect the harness that is labeled resistance from the displacement on demand (DOD) tester to the valve lifter oil manifold connector.
3. Connect the power leads from the DOD tester to B+ and ground. Test for 11-18 ohm on each valve lifter oil manifold solenoid.
瀚慖f not within the specified range for each solenoid, replace the valve lifter oil manifold assembly.
4. Test for infinite resistance between each valve lifter oil manifold circuit terminal and the valve lifter oil manifold housing.
瀚慖f less than infinite resistance, replace the valve lifter oil manifold assembly.
Dynamic Test
1. Ignition OFF, disconnect the harness connector at the valve lifter oil manifold assembly.
2. Connect the cable that is labeled power from the displacement on demand DOD tester to the connector.
3. Connect the power leads from the DOD tester to B+ and ground.
4. Command each valve lifter oil manifold solenoid ON and OFF using the DOD tester. You should be able to hear each solenoid turn ON and
OFF.
瀚慖f the function does not perform as specified, replace the valve lifter oil manifold assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Valve Lifter Oil Manifold Replacement (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and Push Rods/Lifter / Lash
Adjuster/Service and Repair/Valve Lifter Oil Manifold Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming
P3425
DTC P3401, P3425, P3441, or P3449
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P3401
- Cylinder 1 Deactivation Solenoid Control Circuit
瀚慖f not the specified value, test the appropriate control circuit listed below for a short to voltage. If the circuit tests normal, replace the
ECM.
* Cylinder deactivation solenoid valve 1 terminal C
* Cylinder deactivation solenoid valve 2 terminal A
* Cylinder deactivation solenoid valve 3 terminal B
* Cylinder deactivation solenoid valve 4 terminal D
7. Install a 3 A fused jumper wire between the appropriate control circuit terminal listed below and the ignition circuit terminal E. Command the
appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve Control Circuit
High Voltage Test Status parameter displays Malfunction.
* Cylinder deactivation solenoid valve 1 terminal C
* Cylinder deactivation solenoid valve 2 terminal A
* Cylinder deactivation solenoid valve 3 terminal B
* Cylinder deactivation solenoid valve 4 terminal D
瀚慖f not the specified value, test the control circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
8. If all the circuits test normal, test or replace the valve lifter oil manifold assembly.
Component Testing
Static Test
1. Ignition OFF, disconnect the harness connector at the valve lifter oil manifold assembly.
2. Connect the harness that is labeled resistance from the displacement on demand (DOD) tester to the valve lifter oil manifold connector.
3. Connect the power leads from the DOD tester to B+ and ground. Test for 11-18 ohm on each valve lifter oil manifold solenoid.
瀚慖f not within the specified range for each solenoid, replace the valve lifter oil manifold assembly.
4. Test for infinite resistance between each valve lifter oil manifold circuit terminal and the valve lifter oil manifold housing.
瀚慖f less than infinite resistance, replace the valve lifter oil manifold assembly.
Dynamic Test
1. Ignition OFF, disconnect the harness connector at the valve lifter oil manifold assembly.
2. Connect the cable that is labeled power from the displacement on demand DOD tester to the connector.
3. Connect the power leads from the DOD tester to B+ and ground.
4. Command each valve lifter oil manifold solenoid ON and OFF using the DOD tester. You should be able to hear each solenoid turn ON and
OFF.
瀚慖f the function does not perform as specified, replace the valve lifter oil manifold assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Valve Lifter Oil Manifold Replacement (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and Push Rods/Lifter / Lash
Adjuster/Service and Repair/Valve Lifter Oil Manifold Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming
P3425
DTC P3401, P3425, P3441, or P3449
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P3401
- Cylinder 1 Deactivation Solenoid Control Circuit
Monday, November 16, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2138
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2138
瀚慖f less than the specified value, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
BCM.
3. Test for B+ between the B+ circuit terminal 1 and the signal circuit terminal 3.
瀚慖f less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace
the BCM.
4. Ignition OFF, disconnect the X1 harness connector at the BCM.
5. Test for infinite resistance between the signal circuit terminal 3 and ground.
瀚慖f less than the specified value, test the signal circuit for a short to ground.
6. If all circuits test normal, test or replace the steering wheel control switch - left.
Component Testing
Steering Wheel Control Switch - Left
1. Disconnect the harness connector at the steering wheel controls switch - left.
2. Cruise control switch ON, measure the resistance between terminal 1 and terminal 3 while individually activating and holding each cruise
control function switch and compare the resistance reading to the values in the table below.
瀚慖f not within the specified resistance range, replace the steering wheel controls switch - left.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Steering Wheel Control Switch Assembly Replacement (See: Accessories and Optional Equipment/Sensors and Switches - Accessories and
Optional Equipment/Steering Mounted Controls Assembly/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
P0568
DTC P0564, P0567, or P0568
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0564
- Cruise Control Multifunction Switch Circuit
DTC P0567
- Cruise Control Resume Switch Circuit
DTC P0568
- Cruise Control Set Switch Circuit
Diagnostic Fault Information
瀚慖f less than the specified value, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
BCM.
3. Test for B+ between the B+ circuit terminal 1 and the signal circuit terminal 3.
瀚慖f less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace
the BCM.
4. Ignition OFF, disconnect the X1 harness connector at the BCM.
5. Test for infinite resistance between the signal circuit terminal 3 and ground.
瀚慖f less than the specified value, test the signal circuit for a short to ground.
6. If all circuits test normal, test or replace the steering wheel control switch - left.
Component Testing
Steering Wheel Control Switch - Left
1. Disconnect the harness connector at the steering wheel controls switch - left.
2. Cruise control switch ON, measure the resistance between terminal 1 and terminal 3 while individually activating and holding each cruise
control function switch and compare the resistance reading to the values in the table below.
瀚慖f not within the specified resistance range, replace the steering wheel controls switch - left.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Steering Wheel Control Switch Assembly Replacement (See: Accessories and Optional Equipment/Sensors and Switches - Accessories and
Optional Equipment/Steering Mounted Controls Assembly/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
P0568
DTC P0564, P0567, or P0568
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0564
- Cruise Control Multifunction Switch Circuit
DTC P0567
- Cruise Control Resume Switch Circuit
DTC P0568
- Cruise Control Set Switch Circuit
Diagnostic Fault Information
Saturday, November 14, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2097
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2097
瀚慖f less than the specified range, test the appropriate relay coil control circuit for a short to ground. If the circuit tests normal, replace the
K20 ECM.
4. Command the appropriate cooling fan relay ON and OFF with a scan tool. The DMM should transition from OL when commanded OFF to
less than 1 V when commanded ON.
瀚慖f the circuit voltage does not correspond to the specified values, test the control circuit for an open/high resistance or for a short to
voltage. If the circuit tests normal, replace the K20 ECM.
5. If all circuits test normal, test or replace the appropriate KR20 relay.
Component Testing
1. Ignition OFF, disconnect the KR20 cooling fan relay.
2. Test for 70-110 ohm between terminals 85 and 86.
瀚慖f not within the specified range, replace the KR20 cooling fan relay.
3. Measure the resistance between the terminals listed below:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
The DMM should display OL.
瀚慖f less than the specified range, replace the KR20 cooling fan relay.
4. Test the KR20 Fan Control Relay for less than 2 ohm between terminals 30 and 87A.
瀚慖f greater than the specified range, replace the fan control relay.
5. Connect a 20 A fused jumper wire between relay terminal 85 and B+. Connect a jumper wire between relay terminal 86 and ground. Test for
less than 2 ohm between terminals 30 and 87.
瀚慖f greater than the specified range, replace the KR20 cooling fan relay.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay
Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power
Distribution Relay/Service and Repair/Relay Replacement (Within an Electrical Center))
* Underhood Electrical Center or Junction Block Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and
Repair/Removal and Replacement/Underhood Electrical Center or Junction Block Replacement)
* Engine Coolant Fan Replacement (HP2) (See: Engine, Cooling and Exhaust/Cooling System/Radiator Cooling Fan/Service and
Repair/Engine Coolant Fan Replacement)Engine Coolant Fan Replacement (Non-HP2) (See: Engine, Cooling and Exhaust/Cooling
System/Radiator Cooling Fan/Service and Repair/Engine Coolant Fan Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming
P0482
DTC P0480, P0481, or P0482 (with HP2)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0480
- Cooling Fan Relay 1 Control Circuit
瀚慖f less than the specified range, test the appropriate relay coil control circuit for a short to ground. If the circuit tests normal, replace the
K20 ECM.
4. Command the appropriate cooling fan relay ON and OFF with a scan tool. The DMM should transition from OL when commanded OFF to
less than 1 V when commanded ON.
瀚慖f the circuit voltage does not correspond to the specified values, test the control circuit for an open/high resistance or for a short to
voltage. If the circuit tests normal, replace the K20 ECM.
5. If all circuits test normal, test or replace the appropriate KR20 relay.
Component Testing
1. Ignition OFF, disconnect the KR20 cooling fan relay.
2. Test for 70-110 ohm between terminals 85 and 86.
瀚慖f not within the specified range, replace the KR20 cooling fan relay.
3. Measure the resistance between the terminals listed below:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
The DMM should display OL.
瀚慖f less than the specified range, replace the KR20 cooling fan relay.
4. Test the KR20 Fan Control Relay for less than 2 ohm between terminals 30 and 87A.
瀚慖f greater than the specified range, replace the fan control relay.
5. Connect a 20 A fused jumper wire between relay terminal 85 and B+. Connect a jumper wire between relay terminal 86 and ground. Test for
less than 2 ohm between terminals 30 and 87.
瀚慖f greater than the specified range, replace the KR20 cooling fan relay.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay
Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power
Distribution Relay/Service and Repair/Relay Replacement (Within an Electrical Center))
* Underhood Electrical Center or Junction Block Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and
Repair/Removal and Replacement/Underhood Electrical Center or Junction Block Replacement)
* Engine Coolant Fan Replacement (HP2) (See: Engine, Cooling and Exhaust/Cooling System/Radiator Cooling Fan/Service and
Repair/Engine Coolant Fan Replacement)Engine Coolant Fan Replacement (Non-HP2) (See: Engine, Cooling and Exhaust/Cooling
System/Radiator Cooling Fan/Service and Repair/Engine Coolant Fan Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming
P0482
DTC P0480, P0481, or P0482 (with HP2)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0480
- Cooling Fan Relay 1 Control Circuit
Saturday, October 24, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1595
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1595
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Install a 3 A fused jumper wire between the HVIC return circuit terminal 1 and the HVIC source circuit terminal 23.
4. Ignition ON, observe the BECM HVIC Source Current parameter.
瀚慖f the HVIC Source Current parameter indicates current between 5-18 mA, test for proper PIM connector X1 terminal contact at terminal
1 and terminal 23. If the terminal contact tests normal, replace the PIM.
5. Remove the PIM terminal 1 to terminal 23 fused jumper wire.
6. Test for 5-18 mA with a DMM between the HVIC Source circuit terminal 23 and ground.
瀚慖f within the specified range, test the HVIC Return circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
瀚慖f the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Return circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
瀚慖f less than the specified range, test the HVIC Source circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
Important: Removal of the HV manual disconnect lever also opens the HVIC source circuit between X350 and BECM connector X1.
瀚慖f the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Source circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
P1AE3 with or without P1B05 and P1B06
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Ignition ON, observe the BECM HVIC Source Current parameter. The parameter should display less than 5 mA.
瀚慖f the HVIC Source Current parameter indicates current between 5-18 mA test the HVIC Source circuit for a short to ground between
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Install a 3 A fused jumper wire between the HVIC return circuit terminal 1 and the HVIC source circuit terminal 23.
4. Ignition ON, observe the BECM HVIC Source Current parameter.
瀚慖f the HVIC Source Current parameter indicates current between 5-18 mA, test for proper PIM connector X1 terminal contact at terminal
1 and terminal 23. If the terminal contact tests normal, replace the PIM.
5. Remove the PIM terminal 1 to terminal 23 fused jumper wire.
6. Test for 5-18 mA with a DMM between the HVIC Source circuit terminal 23 and ground.
瀚慖f within the specified range, test the HVIC Return circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
瀚慖f the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Return circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
瀚慖f less than the specified range, test the HVIC Source circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
Important: Removal of the HV manual disconnect lever also opens the HVIC source circuit between X350 and BECM connector X1.
瀚慖f the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Source circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
P1AE3 with or without P1B05 and P1B06
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Ignition ON, observe the BECM HVIC Source Current parameter. The parameter should display less than 5 mA.
瀚慖f the HVIC Source Current parameter indicates current between 5-18 mA test the HVIC Source circuit for a short to ground between
Saturday, December 7, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 734
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 734
瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
3. Test for greater than 9 volts between the signal circuit terminal C and ground while commanding the rear window DOWN by using the
window switch on the driver master control.
瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
4. If all circuits test normal, replace the rear window switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Rear Side Door Window Switch Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window Switch
Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
B3824
DTC B3821 or B3824
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B3821 00
- Left Rear Window Relay Power Circuit
DTC B3824 00
- Right Rear Window Relay Power Circuit
Diagnostic Fault Information
瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
3. Test for greater than 9 volts between the signal circuit terminal C and ground while commanding the rear window DOWN by using the
window switch on the driver master control.
瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
4. If all circuits test normal, replace the rear window switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Rear Side Door Window Switch Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window Switch
Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
B3824
DTC B3821 or B3824
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B3821 00
- Left Rear Window Relay Power Circuit
DTC B3824 00
- Right Rear Window Relay Power Circuit
Diagnostic Fault Information
Wednesday, December 4, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 651
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 651
瀚慖f the test lamp is always ON, test the control circuit for a short to ground or a sticking horn switch. If the circuit tests normal, replace the
BCM.
瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage, an open high resistance, or a horn switch which is not closing.
If the circuit tests normal, replace the BCM.
4. If all circuits test normal, replace the underhood fuse block.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Underhood Electrical Center or Junction Block Bracket Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and
Repair/Removal and Replacement/Underhood Electrical Center or Junction Block Bracket Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
B2850
DTC B2850, B2855, B2870, or B2875
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category
DTC Descriptor
DTC B2870 01
- Tilt Up Switch Circuit Short to Battery
DTC B2875 01
- Tilt Down Switch Circuit Short to Battery
Diagnostic Fault Information
Circuit Description
The memory seat module (MSM) receives voltage inputs from the tilt switch based on the position of the switch. The MSM then supplies battery
voltage and a ground to the tilt motor control circuits depending on which direction of movement is requested.
Conditions for Running the DTC
The ignition ON.
Conditions for Setting the DTC
The MSM detects a tilt switch input for more than 30 consecutive seconds after the tilt motor movement has stopped.
Action Taken When the DTC Sets
* The tilt motor will be deactivated.
* Memory recall functions will be disabled.
Conditions for Clearing the DTC
* A current DTC will clear when the failed switch input is no longer active.
* A history DTC will clear after 100 ignition cycles.
瀚慖f the test lamp is always ON, test the control circuit for a short to ground or a sticking horn switch. If the circuit tests normal, replace the
BCM.
瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage, an open high resistance, or a horn switch which is not closing.
If the circuit tests normal, replace the BCM.
4. If all circuits test normal, replace the underhood fuse block.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Underhood Electrical Center or Junction Block Bracket Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and
Repair/Removal and Replacement/Underhood Electrical Center or Junction Block Bracket Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
B2850
DTC B2850, B2855, B2870, or B2875
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category
DTC Descriptor
DTC B2870 01
- Tilt Up Switch Circuit Short to Battery
DTC B2875 01
- Tilt Down Switch Circuit Short to Battery
Diagnostic Fault Information
Circuit Description
The memory seat module (MSM) receives voltage inputs from the tilt switch based on the position of the switch. The MSM then supplies battery
voltage and a ground to the tilt motor control circuits depending on which direction of movement is requested.
Conditions for Running the DTC
The ignition ON.
Conditions for Setting the DTC
The MSM detects a tilt switch input for more than 30 consecutive seconds after the tilt motor movement has stopped.
Action Taken When the DTC Sets
* The tilt motor will be deactivated.
* Memory recall functions will be disabled.
Conditions for Clearing the DTC
* A current DTC will clear when the failed switch input is no longer active.
* A history DTC will clear after 100 ignition cycles.
Wednesday, November 27, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 516
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 516
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the lumbar position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1860
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the lumbar position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1860
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 505
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 505
瀚慖f not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the
MSM.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
3. If all circuits test normal, test or replace the seat adjuster switch.
Component Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open
position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f not the specified value, replace the seat adjuster switch.
3. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f greater than the specified range, replace the adjuster switch switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Power Seat Switch Replacement (with HP2) ()Power Seat Switch Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1820
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1735 01
- Seat Front Up Switch Circuit Short to Battery
瀚慖f not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the
MSM.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
3. If all circuits test normal, test or replace the seat adjuster switch.
Component Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open
position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f not the specified value, replace the seat adjuster switch.
3. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f greater than the specified range, replace the adjuster switch switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Power Seat Switch Replacement (with HP2) ()Power Seat Switch Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1820
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1735 01
- Seat Front Up Switch Circuit Short to Battery
Tuesday, November 26, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 497
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 497
瀚慖f not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the
MSM.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
3. If all circuits test normal, test or replace the seat adjuster switch.
Component Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open
position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f not the specified value, replace the seat adjuster switch.
3. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f greater than the specified range, replace the adjuster switch switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Power Seat Switch Replacement (with HP2) ()Power Seat Switch Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1755
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1735 01
- Seat Front Up Switch Circuit Short to Battery
瀚慖f not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the
MSM.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
3. If all circuits test normal, test or replace the seat adjuster switch.
Component Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open
position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f not the specified value, replace the seat adjuster switch.
3. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f greater than the specified range, replace the adjuster switch switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Power Seat Switch Replacement (with HP2) ()Power Seat Switch Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1755
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1735 01
- Seat Front Up Switch Circuit Short to Battery
Monday, November 18, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 965
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 965
If the DTC is set, perform the RCDLR tire type and pressure selection setup with the scan tool and cycle the ignition. If the DTC resets, replace the
RCDLR.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for RCDLR replacement, setup, and programming
MP 3010-NP0 - Transfer Case
DTC C0569
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC C0569 4B
- System Configuration Error Calibration Not Learned
Circuit/System Description
* This is an internal fault detection of the transfer case shift control module (TCCM). No external circuits are involved.
* This DTC is set anytime a TCCM is replaced or reprogrammed.
* The automatic transfer case (ATC) motor learn procedure must be performed to erase this DTC. The motor learn procedure allows the
module to learn where the shift rails are located.
Conditions for Running the DTC
* Ignition ON.
* System voltage 10.5-18 V.
Conditions for Setting the DTC
The ATC motor learn procedure for a new or reprogrammed TCCM has not been performed.
Action Taken When the DTC Sets
* Mode shifting is disabled until the ATC motor learn procedure has been performed.
* The SERVICE 4WD indicator illuminates.
* No mode position LED's illuminated.
Conditions for Clearing the DTC
The TCCM clears the DTC once the ATC motor learn procedure has been successfully performed.
Reference Information
Schematic Reference
Transfer Case Control Schematics (See: Transmission and Drivetrain/Transfer Case/Diagrams/Electrical Diagrams/MP 3010-NP0 - Transfer Case)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
If the DTC is set, perform the RCDLR tire type and pressure selection setup with the scan tool and cycle the ignition. If the DTC resets, replace the
RCDLR.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for RCDLR replacement, setup, and programming
MP 3010-NP0 - Transfer Case
DTC C0569
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC C0569 4B
- System Configuration Error Calibration Not Learned
Circuit/System Description
* This is an internal fault detection of the transfer case shift control module (TCCM). No external circuits are involved.
* This DTC is set anytime a TCCM is replaced or reprogrammed.
* The automatic transfer case (ATC) motor learn procedure must be performed to erase this DTC. The motor learn procedure allows the
module to learn where the shift rails are located.
Conditions for Running the DTC
* Ignition ON.
* System voltage 10.5-18 V.
Conditions for Setting the DTC
The ATC motor learn procedure for a new or reprogrammed TCCM has not been performed.
Action Taken When the DTC Sets
* Mode shifting is disabled until the ATC motor learn procedure has been performed.
* The SERVICE 4WD indicator illuminates.
* No mode position LED's illuminated.
Conditions for Clearing the DTC
The TCCM clears the DTC once the ATC motor learn procedure has been successfully performed.
Reference Information
Schematic Reference
Transfer Case Control Schematics (See: Transmission and Drivetrain/Transfer Case/Diagrams/Electrical Diagrams/MP 3010-NP0 - Transfer Case)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
Saturday, November 16, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 777
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 777
瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
3. Test for greater than 9 volts between the signal circuit terminal C and ground while commanding the rear window DOWN by using the
window switch on the driver master control.
瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
4. If all circuits test normal, replace the rear window switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Rear Side Door Window Switch Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window Switch
Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
B3824
DTC B3821 or B3824
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B3821 00
- Left Rear Window Relay Power Circuit
DTC B3824 00
- Right Rear Window Relay Power Circuit
Diagnostic Fault Information
瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
3. Test for greater than 9 volts between the signal circuit terminal C and ground while commanding the rear window DOWN by using the
window switch on the driver master control.
瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
4. If all circuits test normal, replace the rear window switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Rear Side Door Window Switch Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window Switch
Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup and programming
B3824
DTC B3821 or B3824
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B3821 00
- Left Rear Window Relay Power Circuit
DTC B3824 00
- Right Rear Window Relay Power Circuit
Diagnostic Fault Information
Thursday, November 14, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 579
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 579
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the lumbar position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2365
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the lumbar position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2365
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
Wednesday, November 13, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 521
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 521
瀚慖f not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the
MSM.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
3. If all circuits test normal, test or replace the seat adjuster switch.
Component Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open
position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f not the specified value, replace the seat adjuster switch.
3. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f greater than the specified range, replace the adjuster switch switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Power Seat Switch Replacement (with HP2) ()Power Seat Switch Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1815
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1735 01
- Seat Front Up Switch Circuit Short to Battery
瀚慖f not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the
MSM.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
3. If all circuits test normal, test or replace the seat adjuster switch.
Component Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open
position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f not the specified value, replace the seat adjuster switch.
3. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f greater than the specified range, replace the adjuster switch switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Power Seat Switch Replacement (with HP2) ()Power Seat Switch Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1815
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1735 01
- Seat Front Up Switch Circuit Short to Battery
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 513
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 513
瀚慖f not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the
MSM.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
3. If all circuits test normal, test or replace the seat adjuster switch.
Component Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open
position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f not the specified value, replace the seat adjuster switch.
3. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f greater than the specified range, replace the adjuster switch switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Power Seat Switch Replacement (with HP2) ()Power Seat Switch Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1750
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1735 01
- Seat Front Up Switch Circuit Short to Battery
瀚慖f not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the
MSM.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
3. If all circuits test normal, test or replace the seat adjuster switch.
Component Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open
position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f not the specified value, replace the seat adjuster switch.
3. Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
* Front vertical upward switch terminal A
* Front vertical downward switch terminal K
* Rear vertical upward switch terminal F
* Rear vertical downward switch terminal J
* Horizontal forward switch terminal D
* Horizontal rearward switch terminal C
* Recline forward switch terminal H
* Recline rearward switch terminal G
瀚慖f greater than the specified range, replace the adjuster switch switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Power Seat Switch Replacement (with HP2) ()Power Seat Switch Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1750
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1735 01
- Seat Front Up Switch Circuit Short to Battery
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 471
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 471
瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
4. If all circuits test normal, test or replace the Run/Crank relay.
Component Testing
1. Ignition OFF, disconnect the Run/Crank relay.
2. Test for 70-150 ohms between terminals 85 and 86.
瀚慖f the resistance is not within the specified range, replace the relay.
3. Test for infinite resistance between the following terminals:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
瀚慖f less than specified, replace the relay.
4. Install a 3-amp fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground.
Measure for less than 5 ohms between terminals 30 and 87.
瀚慖f greater than specified, replace the relay.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
Refer to Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
B1433
DTC B1433
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC B1433 00
- Ignition Switched Power Relay 2 Circuit
Diagnostic Fault Information
Circuit/System Description
The body control module (BCM) supplies voltage to the HVAC module and the windshield washer solvent heater (RPO XA7). Voltage is applied
when any of the following conditions are true:
* Ignition Switch is in ACC or RUN.
* The vehicle was remote started.
* The vehicle is in retained accessory power (RAP) mode.
Conditions for Running the DTC
瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the
BCM.
4. If all circuits test normal, test or replace the Run/Crank relay.
Component Testing
1. Ignition OFF, disconnect the Run/Crank relay.
2. Test for 70-150 ohms between terminals 85 and 86.
瀚慖f the resistance is not within the specified range, replace the relay.
3. Test for infinite resistance between the following terminals:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
瀚慖f less than specified, replace the relay.
4. Install a 3-amp fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground.
Measure for less than 5 ohms between terminals 30 and 87.
瀚慖f greater than specified, replace the relay.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
Refer to Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
B1433
DTC B1433
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC B1433 00
- Ignition Switched Power Relay 2 Circuit
Diagnostic Fault Information
Circuit/System Description
The body control module (BCM) supplies voltage to the HVAC module and the windshield washer solvent heater (RPO XA7). Voltage is applied
when any of the following conditions are true:
* Ignition Switch is in ACC or RUN.
* The vehicle was remote started.
* The vehicle is in retained accessory power (RAP) mode.
Conditions for Running the DTC
Thursday, October 31, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1696
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1696
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Install a 3 A fused jumper wire between the HVIC return circuit terminal 1 and the HVIC source circuit terminal 23.
4. Ignition ON, observe the BECM HVIC Source Current parameter.
锟斤拷If the HVIC Source Current parameter indicates current between 5-18 mA, test for proper PIM connector X1 terminal contact at terminal
1 and terminal 23. If the terminal contact tests normal, replace the PIM.
5. Remove the PIM terminal 1 to terminal 23 fused jumper wire.
6. Test for 5-18 mA with a DMM between the HVIC Source circuit terminal 23 and ground.
锟斤拷If within the specified range, test the HVIC Return circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
锟斤拷If the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Return circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
锟斤拷If less than the specified range, test the HVIC Source circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
Important: Removal of the HV manual disconnect lever also opens the HVIC source circuit between X350 and BECM connector X1.
锟斤拷If the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Source circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
P1AE3 with or without P1B05 and P1B06
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Ignition ON, observe the BECM HVIC Source Current parameter. The parameter should display less than 5 mA.
锟斤拷If the HVIC Source Current parameter indicates current between 5-18 mA test the HVIC Source circuit for a short to ground between
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Install a 3 A fused jumper wire between the HVIC return circuit terminal 1 and the HVIC source circuit terminal 23.
4. Ignition ON, observe the BECM HVIC Source Current parameter.
锟斤拷If the HVIC Source Current parameter indicates current between 5-18 mA, test for proper PIM connector X1 terminal contact at terminal
1 and terminal 23. If the terminal contact tests normal, replace the PIM.
5. Remove the PIM terminal 1 to terminal 23 fused jumper wire.
6. Test for 5-18 mA with a DMM between the HVIC Source circuit terminal 23 and ground.
锟斤拷If within the specified range, test the HVIC Return circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
锟斤拷If the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Return circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
锟斤拷If less than the specified range, test the HVIC Source circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
Important: Removal of the HV manual disconnect lever also opens the HVIC source circuit between X350 and BECM connector X1.
锟斤拷If the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Source circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
P1AE3 with or without P1B05 and P1B06
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Ignition ON, observe the BECM HVIC Source Current parameter. The parameter should display less than 5 mA.
锟斤拷If the HVIC Source Current parameter indicates current between 5-18 mA test the HVIC Source circuit for a short to ground between
Wednesday, October 30, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3106
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3106
瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
EBCM.
3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.
瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
4. If all circuits test normal, replace the yaw rate sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/GMLAN Wiring Repairs)
* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and
Operation/ABS Description and Operation) for the ABS - Hybrid
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg
(8600 lb) GVW
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to
3900 kg (8600 lb) GVW
* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming
U2156
DTC U2105-U2199
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC U2142 00
- Lost Communication With Yaw Rate Sensor (YRS)
Circuit/System Description
Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be
exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an
availability indication of the transmitter module. Each message contains the identification number of the transmitter module.
The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the
ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus
serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain
Management/Computers and Control Systems/Information Bus/Description and Operation).
Conditions for Running the DTC
* The system voltage is between 9-16 volts.
* The vehicle power mode master requires serial data communication to occur.
Conditions for Setting the DTC
A supervised periodic message that includes the transmitter module availability has not been received.
Action Taken When the DTC Sets
* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.
* System OFF lamps will illuminate for these systems.
瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
EBCM.
3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.
瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
4. If all circuits test normal, replace the yaw rate sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/GMLAN Wiring Repairs)
* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and
Operation/ABS Description and Operation) for the ABS - Hybrid
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg
(8600 lb) GVW
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to
3900 kg (8600 lb) GVW
* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming
U2156
DTC U2105-U2199
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC U2142 00
- Lost Communication With Yaw Rate Sensor (YRS)
Circuit/System Description
Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be
exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an
availability indication of the transmitter module. Each message contains the identification number of the transmitter module.
The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the
ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus
serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain
Management/Computers and Control Systems/Information Bus/Description and Operation).
Conditions for Running the DTC
* The system voltage is between 9-16 volts.
* The vehicle power mode master requires serial data communication to occur.
Conditions for Setting the DTC
A supervised periodic message that includes the transmitter module availability has not been received.
Action Taken When the DTC Sets
* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.
* System OFF lamps will illuminate for these systems.
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1586
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1586
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Install a 3 A fused jumper wire between the HVIC return circuit terminal 1 and the HVIC source circuit terminal 23.
4. Ignition ON, observe the BECM HVIC Source Current parameter.
锟斤拷If the HVIC Source Current parameter indicates current between 5-18 mA, test for proper PIM connector X1 terminal contact at terminal
1 and terminal 23. If the terminal contact tests normal, replace the PIM.
5. Remove the PIM terminal 1 to terminal 23 fused jumper wire.
6. Test for 5-18 mA with a DMM between the HVIC Source circuit terminal 23 and ground.
锟斤拷If within the specified range, test the HVIC Return circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
锟斤拷If the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Return circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
锟斤拷If less than the specified range, test the HVIC Source circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
Important: Removal of the HV manual disconnect lever also opens the HVIC source circuit between X350 and BECM connector X1.
锟斤拷If the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Source circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
P1AE3 with or without P1B05 and P1B06
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Ignition ON, observe the BECM HVIC Source Current parameter. The parameter should display less than 5 mA.
锟斤拷If the HVIC Source Current parameter indicates current between 5-18 mA test the HVIC Source circuit for a short to ground between
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Install a 3 A fused jumper wire between the HVIC return circuit terminal 1 and the HVIC source circuit terminal 23.
4. Ignition ON, observe the BECM HVIC Source Current parameter.
锟斤拷If the HVIC Source Current parameter indicates current between 5-18 mA, test for proper PIM connector X1 terminal contact at terminal
1 and terminal 23. If the terminal contact tests normal, replace the PIM.
5. Remove the PIM terminal 1 to terminal 23 fused jumper wire.
6. Test for 5-18 mA with a DMM between the HVIC Source circuit terminal 23 and ground.
锟斤拷If within the specified range, test the HVIC Return circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
锟斤拷If the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Return circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
锟斤拷If less than the specified range, test the HVIC Source circuit for an open between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
Important: Removal of the HV manual disconnect lever also opens the HVIC source circuit between X350 and BECM connector X1.
锟斤拷If the circuit tests normal, perform the High Voltage Disabling () procedure and test the HVIC Source circuit for an open between X350
and BECM connector X1. If the circuit tests normal, replace the BECM.
P1AE3 with or without P1B05 and P1B06
Important: DTCs P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Ignition ON, observe the BECM HVIC Source Current parameter. The parameter should display less than 5 mA.
锟斤拷If the HVIC Source Current parameter indicates current between 5-18 mA test the HVIC Source circuit for a short to ground between
Subscribe to:
Posts (Atom)